815517
10
Zoom out
Zoom in
Previous page
1/32
Next page
10 02/237033-351J
It is very important to reload your appliance while
enough lively hot coals remain in order to provide the
amountofheatneededtodryandrekindlethenextload
ofwood.ItisbesttoopentheBurnRateAirandStart-
Up Air Controls before reloading. This livens up the coal
bedandreducesexcessiveemissions(opacity/smoke).
Opendoorslowly so that ash orsmokedoesnotexit
appliancethroughopening.Youshouldalsobreakup
any large chunks and distribute the coals so that the
new wood is laid on hot coals.
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly.
To do this we need to learn to burn our appliances in
the cleanest way possible. Doing this will allow us to
continue using our wood appliances for many years to
come.
2. Medium low burn setting:
- BurnRateAirControlspringhandleuptohighposition
for 5 minutes.
- Then activate the ACC timer system by pushing the
knob all the way back toward the appliance to “HI”
then pull forwards towards the front of the appliance
untiltheknobstops.
- Atthatpoint move theBurnRateAirControlspring
handleto1/8”-1/2”fromthelowsetting.
3. Medium high burn setting:
- BurnRateAirControlspringhandleuptohighposition.
- Then activate the ACC timer system by pushing the
knob all the way back toward the appliance to “HI”
then pull forwards towards the front of the appliance
untiltheknobstops.
- Atthatpoint move theBurnRateAirControlspring
handleto1/2”–high.
4. High burn setting:
- BurnRateAirControlspringhandleuptohighposition
- AlsoactivateACCtimersystemknobpushedbackto
the“HI”position.
Surface Thermometer is a Valuable Guide to Operation
A surface thermometer tells you when to adjust the air
control, and when to refuel, Figure 10.1.
For example, when the thermometer registers at least 450°F
(230°C)onthestovetopafterstart-upyouknowthestove
is hot enough and it may be time to adjust the air control
ifasufcientember bed has also been established. Note
that the stove will warm up much sooner than the chimney,
though;awarmchimneyisthekeytoeasy,effectivestove
operation.Whenthermometerreadingsdropbelow350°F.
(175°C) it’s time to adjust the air control for a higher burn
rate or to reload the stove. A temperature reading over
650°F. (340°C) is a sign to reduce the air supply to slow the
burn rate.
Usethefollowingtemperaturerangesasaguide:
Readings in the 350°-500°F. (175°-260°C) range indicate
low to medium heat output.
500°-600°F. (260°-315°C) readings indicate medium
heat output.
Readings of 600°-650°F. (315-340°C) indicate high
heatoutput.Operatingyourwoodstovecontinuouslyat
stove top temperatures higher than 650° F (340°C) may
damage your wood stove.
NOTE: The above information is provided as a guideline
only. Altitude and other circumstances may require
control adjustments to achieve the desired burn rates.
NOTE: Operate appliance on High Burn 45 minutes a
daytohelpkeepue/chimneyclean.
NOTE: If using the optional blower, for burn rate settings
1-3,theblower shall be offfor the rst30minutesand
then be operated in the high position at 30 minutes. For
high burn setting, blower may continue to be on full after
the loading of the fuel.
D. Burn Rates and Operating Efciency
For maximum operating efciency
This wood appliance has a manufacturer-set minimum
low burn rate that must not be altered. It is against federal
regulations to alter this setting or otherwise operate this
wood appliance in a manner inconsistent with operating
instructions in this manual.
• Burndry,well-seasonedwood.
Burn Rates
1. Low burn setting:
- BurnRateAirControlspringhandleuptohighposition
for 5 minutes.
- Then activate the ACC timer system by pushing the
knob all the way back toward the appliance to “HI”
then pull forwards towards the front of the appliance
untiltheknobstops(Figure 10.1).
- AtthatpointclosetheBurnRateAirControlbymoving
the spring handle to the low setting.
Figure 10.1
HIGH
MED
LOW
Burn Rate
Air Control
Start-Up
Air Control
Surface
Thermometer
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire 3100 Millennium at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire 3100 Millennium in the language / languages: English as an attachment in your email.

The manual is 5.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire 3100 Millennium

Quadra-Fire 3100 Millennium User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info