TIMER MODE
B
C
Set time
D
ADJUSTABLE TIMER SETTING
D
PRESET TIMER SETTING
Select the preset time.
D
Selection of the preset time/
adjustable timer
15 min. 10 min.
➾
➾
➾
3 min. ➾ 5 min.
➾
Adjustable
timer
Select the adjustable timer.
▲
Press for 2 to 3 seconds.
B
▲
C
▲
▲
D
Set the flashing digits.
Return to TIMER mode.
▲
B
Select the digits to be adjusted
(hour/minutes).
No. of times
the countdown
is repeated
Time measured
TIMER OPERATION
B
C
Start / Stop / Restart
D Reset
* When the set time is up, a warning sound beeps for 5 seconds.
To stop it manually, depress any one of the buttons.
● After the set time is up, the timer counts down the set time repeatedly. After the timer
is used, therefore, be sure to reset it as the battery energy is consumed enormously
to shorten the battery life.
● In the adjustable timer setting, the flashing digits move quickly if button D is kept
pressed.
● If the watch is left untouched with the digits flashing, it will automatically return to the
TIMER mode in 2 to 3 minutes.
● Restart and stop of the timer can be repeated by pressing button C.
● The display will be turned off 2 seconds after a button is pressed. To check the data
on the display, press button E.
● After the countdown is repeated 99 times, the number of times the countdown is
repeated is displayed in 2 digits such as “00 ” for 100, “01 ” for 101, and so on.
● When the button operation confirmation sound is turned on, a beep sounds every
minute to signal the lapse of time.
● Even if the TIMER mode is changed to another while the measurement is in progress,
it continues counting properly and the flashing TIMER mode mark indicates that the
timer is in use. After the timer is used, however, be sure to reset it as the battery
energy is consumed enormously to shorten the battery life.
● If the timer is left counting without being stopped, it will automatically be stopped and
reset to show the set time when more than 12 hours passed and the time display
reaches 0:00 a.m. or 0:00 p.m.
ALARM MODE
ALARM SETTING
Press for 2 to 3 seconds.
B
▲
C
▲
D
B
Set the flashing digits.
Return to ALARM mode.
▲
* The alarm is automatically engaged.
Select the digits to be adjusted
(hour/minutes).
● Two types of timer are available: preset timer and adjustable timer.
● The adjustable timer can be set up to 9 hours and 59 minutes in minute increments.
The IC (Integrated Circuit)
used in your watch will be
affected by static electricity
which may disturb the
display. Keep the watch
STATIC ELECTRICITY
away from close contact with objects
such as TV screens which emit strong
static electricity.
CAUTION
● The battery is not rechargeable. Never attempt to recharge it, as this may
cause battery leakage or damage to the battery.
WARNING
● Do not remove the battery from the watch.
● If it is necessary to take out the battery, keep it out of the reach of children. If
a child swallows it, consult a doctor immediately.
● Never short-circuit, tamper with or heat the battery, and never expose it to fire.
The battery may burst, become very hot or catch fire.
● Necessary procedure after battery change
After the battery is replaced with a new one, or if an abnormal display (broken digits, etc.) appears,
follow the procedure below to reset the IC.
Press and hold buttons A, B, C and D at the same time for
2 to 3 seconds. The display shown at right appears.
* Before using the watch, set the time/calendar and alarm.
●
The battery life may be less than 2 years if the stopwatch is used for more than 10 hours a day,
the timer for more than 10 hours a day, the alarm more than once a day, the illuminating light more
than 3 times a day, the confirmation sound more than 24 times a day and/or the auto illumination
more than 30 times a week.
●
If the illuminating light is not turned on by pressing any of the buttons, replace the battery with
a new one as the battery has run down.
●
As the battery is inserted at the factory to check the function and performance of the watch, its
actual life once in your possession may be less than the specified period.
●
When the battery expires, be sure to replace it as soon as possible to prevent any malfunction.
●
We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement.
CARE OF CASE AND BRACELET
To prevent possible rusting of
the case and bracelet caused
by dust, moisture and
perspiration, wipe them
periodically with a soft dry cloth.
PERIODIC CHECK
It is recommended that the
watch be checked once
every 2 to 3 years. Have
your watch checked by an
AUTHORIZED PULSAR
2 - 3
Years
DEALER or SERVICE CENTER to
ensure that the case, buttons, gasket
and crystal seal remain intact.
CHEMICALS
Be careful not to expose the
watch to solvents, mercury,
cosmetic spray, detergents,
adhesives or paints.
Otherwise, the case,
bracelet, etc. may become discolored,
deteriorated or damaged.
MAGNETISM
The watch will not be
affected by magnetism.
N
S
LIQUID CRYSTAL PANEL
The normal life expectancy
for the liquid crystal panel
of the watch is approxi-
mately 5 years. After that
it may decrease in contrast,
5 Years
becoming difficult to read. Please
contact your AUTHORIZED PULSAR
DEALER or SERVICE CENTER if you
wish to have a new panel fitted
(guaranteed one year).
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM
If your watch
protective
sticker on the case back, be
sure to peel them off before
using your watch.
SHOCKS & VIBRATION
Light activities will not affect
your watch, but be careful
not to drop your watch or
hit it against hard surfaces,
as this may cause damage.
TEMPERATURES
+50°C
-5°C
Your
of 5° C and 35° C (41° F and 95° F).
Temperatures over 50° C (122° F) or below –5° C (+23° F) may
cause a slight time loss or gain or battery leakage or shorten the
battery life.
However, the
returns to normal temperature.
WATER RESISTANCE
● Non-water resistant
• If the watch becomes wet, have it checked by an AUTHORIZED
PULSAR DEALER or SERVICE CENTER.
● Water resistant 5/10/15/20 bar
5
bar WR
10/15/20
bar WR
• Do not operate the buttons when the watch is wet or in water.
If used in sea water, rinse the watch in fresh water and dry it completely.
• When taking a shower with the water resistant 5 bar watch, or taking
a bath with the water resistant 10, 15 or 20 bar watch, be sure to
observe the following:
* Do not operate the buttons when the watch is wet with soapy water
or shampoo.
* If the watch is left in warm water, a slight time loss or gain may be
caused. This condition, however, will be corrected when the watch
returns to normal temperature.
TO PRESERVE THE QUALITY OF YOUR WATCH
* Pressure in bar is a test pressure and should not be considered as corresponding
to actual diving depth since swimming movement tends to increase the pressure
at a given depth. Care should also be taken on diving into water.
** We recommend that you wear a PULSAR Diver’s Watch for scuba diving.
▲
Current
time
Battery life : Approx. 2 years
Battery : SEIKO CR2025
2
Y
BATTERY CHANGE
D
BC
“A” (AM)/“P” (PM) mark
Set alarm time
Alarm engagement/disengagement
With each press, the alarm is engaged
and disengaged alternately.
C
Alarm engaged
Alarm mark
“on” mark
Turning on/off of hourly time signal and
button operation confirmation sound
C
With each press in TIME/CALENDAR
mode, the hourly time signal and button
operation confirmation sound are turned
on and off alternately.
Hourly time
signal mark
● At the designated time the alarm rings for 20 seconds, and the display is illuminated as the
alarm rings. To stop them manually, press any one of the buttons.
● In the alarm time setting, the flashing digits move quickly if button D is kept pressed.
● When the time function is displayed in the 24-hour indication, the alarm is also displayed
in the 24-hour indication.
● When setting the hour digits in the 12-hour indication, check that AM/PM is properly set.
● If the watch is left untouched with the digits flashing, it will automatically return to the
ALARM mode in 2 to 3 minutes.
● Alarm test: The alarm can be tested by keeping buttons C and D pressed in the TIME/
CALENDAR mode.
● When the hourly time signal mark is displayed, the hourly time signal rings every hour on
the hour and the confirmation sound beeps with each press of the buttons.
