572632
4
Zoom out
Zoom in
Previous page
1/8
Next page
6
7
The device was designed for extensive usage. To ensure longevity and
performance, please adhere to the following:
GUIDELINES FOR OPERATION
INSTALLATION OF BATTERIES
EXTERNAL POWER SUPPLY
Before use make sure that you have installed the digital module
according to the instructions of the section 8.
Store with the lens cap on in the carrying case.
Switch off the unit after use.
The unit cannot be submerged in water.
Attempts to disassemble or repair the unit will void the warranty!
Clean the device's optical surfaces only if necessary, and use caution.
First, remove (by blowing with a blower brush or canned air) any dust or
sand particles. Then proceed to clean by using camera/lens cleaning
equipment approved for use with multicoated lenses. Do not pour the
solution directly onto the lens!
The device can be used in operating temperatures ranging from
-25 °C... +50 °C. However, if it has been brought indoors from cold
temperatures, do not turn it on for 3 to 4 hours. This will prevent external
optical surfaces from fogging.
To ensure reliable performance, it is recommended to carry out regular
technical inspections of the unit.
Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
Turn the lever (8) of the battery container (11) 90 degrees in “Open”
position and, pulling by the lug of the cover, remove the battery container.
Install four AA batteries (or rechargeable batteries) observing marking
shown on the battery container.
Insert the battery container into the battery compartment observing
polarity and turn the l ever 90 degrees clockwise .
Note: to ensure long and reliable operation it is recommended that you use
quality rechargeable batteries with a capacity of at least 2500 mAh. Please
do not use batteries of different types or batteries with various charge
levels.
The device can be powered with an external DC power supply
(2.1mm pin) with stabilised voltage ranging from 8.4V to 15V
or a 12V vehicle socket.
External power supply (AC/DC) is to be connected to “Power” (9) jack
located on the right side of the device.
Please note that the central pin of the power supply that you
connect to the “power” jack of the unit, must have marking
“+”. The power supply may have marking .
Connection of an external power supply (icon shows up on the data
panel) automatically cuts off power supply from batteries.
External power supply DOES NOT charge the rechargeable batteries
in the unit.
Attention! We suggest that you use battery packs EPS3 or EPS5
ensuring from 7 to 18 hours of operation.
PWR
10
17
24
25
MOUNTING THE MONOCULAR ON DIGITAL MODULE
The monocular Pulsar 10x32 (included) converts the digital module into a
digital night vision device with 10x magnification.
Insert the monocular firmly so that the pins (24) in the monocular’s body
enter the notches (17) of the digital module and the groove (25) coincides
with the lock (10) (see pic.).
Turn the monocular counterclockwise so that the lock (10) snaps.
In order to remove the monocular, move the lock (10) sideways and turn
the monocular clockwise until it clicks.
Pull the pins (24) out of the monocular’s notches (17) and remove the
monocular c arefully.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pulsar Forward DN55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Forward DN55 in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info