572627

Pulsar Digisight LRF N870 Manual

8
Zoom out
Zoom in
Previous page
1/50
Next page
12
13
Reticle colour selection
This option allows you to switch between four reticle colour options.
To select one of the colour options, press the controller button (7) and rotate
the controller.
Colour options are as follows:
Option 1 - main part of the reticle is black, additional part is red;
Option 2 - main part of the reticle is black, additional part is green;
Option 3 - main part of the reticle is white, additional part is green;
Option 4 - main part of the reticle is white, additional part is red.
Weapon tilt indicator
This option allows you to activate/deactivate the weapon tilt indicator.
Weapon tilt is indicated by “sector” arrows on the edges of the horizontal line of
the reticle (see image). Arrows show the direction in which you should move your
rifle to eliminate tilt.
There are three modes of weapon tilt indication:
5°-10° - one sector arrow;
10°-20° - two sector arrow;
>20° - three sector arrow.
A tilt of less than 5° is not shown on the display.
Brightness control of onscreen symbols
To select option, rotate the controller (7) and press controller button.
Rotate the controller to select brightness level of icons – from 1 to 10.
Confirm choice by a short press of the controller button.
Menu М2 options
One shot zeroing
Please refer to section 10 “ZEROING”
Zeroing with “Freeze” function
Before using this function, please take a shot.
Select “Freeze” function in menu M1.
Riflescope will prompt you to press any button on the riflescope or wireless
control within 30 seconds to freeze (memorize) the image. The status bar shows
corresponding icon.
Before pressing a button match the reticle of the riflescope with the aiming
point (as a rule - target centre). After button is pressed, the image “freezes” and a
limiting frame with an auxiliary cross appear.
Note: after the image is “frozen”, there is no need to aim at the target.
Rotating the controller, move the auxiliary cross within the limiting frame until
the cross matches the point of impact.
Short press of the controller button allows you to switch direction of auxiliary
cross (horizontal or vertical). Long press of the controller button saves zeroing
settings and exits the menu.
Saving the settings is confirmed with “Ok” message displayed instead of the
coordinates.
After exiting the menu, the image returns to normal.
Selection/disable of video output signal
Press the controller button and rotate it to select output video signal – PAL or
NTSC (video output is disabled by default).
To disable the video output, select option “OFF”. Disabled video output
reduces power consumption.
Confirm your choice by a short press of the controller button.
Clock setup
Press the controller button (7) and rotate the controller to select time format
24/AM/PM.
Press the controller button to proceed to hour setup. Set the hour value
rotating the controller.
Press the controller button to proceed to minute setup. Set the minute value.
To exit submenu, hold down the controller (7) for two seconds. Or wait ten
seconds to exit automatically.
Remote control activation
Wireless remote control duplicates functions of riflescope and IR Illuminator
on/off and rangefiner on/off/distance measuring.
It has three buttons:
Button “ON” (17) – turning riflescope on/off (press for two seconds to
activate).
Button “IR” (18) - turning IR Illuminator on/off, selecting power level.
Rangefinder ON-OFF /Distance measuring button (19).
To start using the wireless remote control you will need to activate it:
Turn on the scope and select menu option “RC activation”.
Press controller button, a message “WAIT” will show up and countdown will
start within which you need to press any button of the RC.
If the activation is successful, a message “Complete” will show up next
to icon. If a message “ERROR” appears, repeat activation procedure.
The RC is ready for use.
Automatic shutoff
This option allows you to activate automatic on/off of the riflescope which
recognizes whether your riflescope is in a shooting position.
The automatic on/off function is actuated 10 seconds after you move the
riflescope relative to the optical axis:
Upwards > 70°; Downwards >70°; Leftwards >30°; Rightwards >30°
To select option, rotate the controller (7) and press controller button.
Rotate the controller (7) to select “Yes” and press the controller button.
Message AUTO appears in the status bar.
To disable the function, select “Off”.
Assignment of the functional button
This button allows you to assign to the button (8) one of the three functions:
1. “SumLight™”
2. “Automatic contrast”
3. “Reticle colour”.
Rotate the controller to select required function.
Press the controller button to confirm.
Default setting of button (8) is SumLight™ function.
Menu М3 options
THD” function (True horizontal distance)
“THD” function allows the user to measure true horizontal distance to a target
based on the angle of elevation value.
To select the function, press the controller button, select ON.
Confirm your choice by a short press of the controller button. Hereinafter
message THD will appear above the distance readings.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pulsar Digisight LRF N870 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Digisight LRF N870 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info