782198

Proxxon DSH-E Manual

14
Zoom out
Zoom in
Previous page
1/20
Next page
- 14 -
Round sawing blades (with flat ends) can ideally be used for
plastic, hard and soft wood. They cut on all sides, so it is not
necessary to turn the work piece when sawing.
10 Selecting the speed:
This representation can, of course, only give instructions on
the general direction to take. As in the previous section, you
have to "experiment” a little to find the optimal result. The
appropriate speed also, of course, depends on the blade
used, the material of the work piece, the feed etc.
Level Material
400 strokes Steel, brass, non-ferrous
metals, GRP, plastics
1600 strokes Aluminium, wood, polystyrene,
rubber, leather, cork
10.1.1 Possible causes of faults:
The following causes may break the saw blade:
– If blade is tensioned too tightly or not tightly enough
– Mechanical overloading of the blade by feeding too quickly.
– Bending or twisting of the blade when turning the work
piece too quickly when cutting curves.
– When the wear limit of the saw blade has been reached.
– If the screws are tightened on saw blades with cross pin.
10.2 Sawing (fig. 7)
Hold the work piece on the saw table as shown in fig. 7.
Adapt the feed according to the material, the saw blade and
the work piece thickness. Hard materials, fine saw blades and
thick work pieces do not “tolerate” as much feed as soft
materials, rough saw blades and thin materials.
You can also experiment with various speeds.
NOTE:
Safe and precise work is only possible with careful fixing!
The mechanical scroll saw is predominantly a machine for
sawing curves. For good results, please note the following
points:
Please note:
– Only use perfect saw blades.
– Always remove the mains plug for maintenance and upkeep
work.
– Do not let the device operate unsupervised.
1. When sawing, press the work piece onto the work plate,
guide by feeling and with little power, more pressure on the
work plate, less pressure against the saw blade. Caution!
The saw does not cut the work piece itself. You must guide
the work piece into the saw blade.
2. Guide the work piece slowly into the saw blade, particularly
if the blade is very thin and the teeth very fine or if the work
piece is very thick. You will achieve the best results if the
wood thickness is less than 25 mm.
3. Please observe the instructions under 8.1.
10.2.1 Inside cuts (fig. 8)
CAUTION!
Always remove the mains plug before releasing the saw
blade.
If you must also make inside cuts when working with your
mechanical scroll saw, proceed as follows:
1. Drill a hole in the inside part 1 to be cut out of your work
piece.
2. Take the saw blade from the top saw blade guide 2.
Proceed as shown in 8.7.5.1 and in 8.7.5.2, depending on
the type of saw blade used.
3. Push the saw blade through the drill hole. Reattach saw
blade at the top. Tension the saw blade properly again.
4. Cut out the opening and remove the work piece once the
saw blade has been removed again.
Tip: If you drill the hole in such a way that it does not touch
the later inside contour, you can allow the saw line to run
tangentially into the contour. This produces a nice even
sawing edge.
10.2.2 Grain cuts:
For grain cuts, the table is simply tilted by the required
amount. This works as follows:
1. Slightly loosen toggle screw 1 (fig. 2) and align saw table 2
to the required value, using scale 9 on indicator 8.
2. Tighten toggle screw 1.
3. Press the work piece particularly firmly against the table for
a grain cut.
Proxxon_BedienAnl_DSH_US_Bel 10.06.2005 14:20 Uhr Seite 14
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proxxon DSH-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proxxon DSH-E in the language / languages: English as an attachment in your email.

The manual is 1.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Proxxon DSH-E

Proxxon DSH-E User Manual - German - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info