634706
48
Zoom out
Zoom in
Previous page
1/73
Next page
8.2 IE Remote Surveillance
In order to view the NVR from a network it must be connected to a LAN/WAN or internet. The network
setup should be done accordingly. Please refer to 5.6 Network Setup. This NVR supports IE browser, on
Windows XP and Vista platform.
8.2.1 On LAN
Step 1: Enter into the NVR’s Main MenuSetupNetwork tab to input IP address, Subnet Mask, etc .If
using DHCP, please enable DHCP in both the NVR and the router.
Step 2: Enter Record Setup to set network video parameters like resolution, frame rate etc.
Step 3: Open IE on a computer on the same network. Input the IP address of the NVR in IE address bar and
press enter.
Step 4: IE will download ActiveX component automatically. Enter the username and password in the
subsequent window.
Notice: If HTTP port is not 80, other number instead, need add the port number after IP address. For example, set HTTP port as 82,
need input IP address like 192.168.0.25:82.
User name and password here are the same with that used on the NVR. The default is admin and 123456.
8.2.2 On WAN
There are two ways for the NVR to connect to internet.
1. Connect the NVR to internet through router or virtual server
Step 1: Enter into the NVR’s Main MenuSetupNetwork interface to input IP address, Subnet Mask, etc.
If using DHCP, please enable DHCP in both the NVR and router.
Step 2: Forward IP address and port number in Virtual Server setup of the router or virtual server. Configure
the firewall to allow accessing the NVR.
Note: Port forwarding settings may be different in different routers and server. Please refer to the router’s manual for details.
Step 3: Open IE browser, input IP address, or dynamic domain name and enter. If HTTP port is not 80, add
the port number after IP address or domain name.
Step 4: IE will download ActiveX automatically. Then a window pops up and asks for user name and
password. Input name and password correctly, and enter to view.
Note: If you cannot download and install ActiveX, please refer to FAQ Q8.
2. Connect the NVR to internet through PPPoE directly.
Step 1: Enter into the NVR’s Main MenuSetupNetwork interface to enable PPPoE and then input user
name and password received from your ISP. Next, click Apply’. The NVR will connect to the server and
would give a confirmation message.
Step 2: When accessing the remote interface of NVR, user can input WAN IP to access directly (user can
enter into Main menuInformationNetwork interface to check IP address).
Step 3: If users want to utilize dynamic domain name, please apply for a domain name in a DNS server
supported by the NVR or router. Then add to the NVR.
Step 4: The following setting steps are as the same as Step3 and Step 4 in Point 1.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Provision ISR NVR-16400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Provision ISR NVR-16400 in the language / languages: English as an attachment in your email.

The manual is 4,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info