490687

Protool WCP50 Manual

13
Zoom out
Zoom in
Previous page
1/90
Next page
13
8.1 Smooth start-up
After switching on the machine, regulation elec-
tronic circuits provide for a smooth start-up up to
the operating speed without unnecessary kicks.
This decreases the wear of gears, and increases
machine lifetime.
8.2 Limitation of start-up current
The electronically controlled smooth start-up en-
sures that the machine starts up without a kick.
Due to limited start-up current of the machine, a
protection rating of 10 A is suffi cient.
8.3 Overload protection
Is the tool overloaded, the oveload protection is
actuated, and the tool stops. When the load is
removed, the tool restarts automatically. Before
you continue in your work, you should let the tool
reach full speed.
8.4 Thermal overload protection
If you work with the tool for longer periods of
time under excessive load conditions, the motor is
switched off by the thermal protection that protects
the motor from overheating.
After having cooled down, i.e. after about 30 sec-
onds, the machine can be restarted again.
Causes of overheating: excessive pressure, de-
viation of tool from perpendicular position, bad
quality or excessive wear of disc.
9 Maintenance
- The unit should be stored in a dry place where
it is protected against freezing.
- The ventilation holes on the motor casing must
not get blocked up.
- The cable may only be replaced in a specialised
electrical workshop qualifi ed to perform such
work.
After approx. 200 hours of use the following main-
tenance work must be performed:
- Check the length of the brushes. Brushes shorter
than 5 mm should be replaced.
- The machine turns itself off automatically when
the brushes are worn out. The machine must be
sent to a service centre for maintenance.
WARNING
To preserve the protection class the machine
must undergo a safety inspection; this must
be done in a specialised electrical workshop
qualifi ed to perform such work.
- Service – see enclosed sheet.
10 Environmental Protection /
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into house-
hold waste!
According to the European Directive 2002/96/EC
on waste electrical and electronic equipment and
its incorporation into national law, power tools that
are no longer suitable for use must be separately
collected and sent for recovery in an environmen-
tal-friendly manner.
REACh
REACh is a European Chemical Directive that
came into effect in 2007. As “downstream users”
and product manufacturers, we are aware of our
duty to provide our customers with information.
We have set up the following website to keep you
updated with all the latest news and provide you
with information on all the materials used in our
existing products:
http://www.tts-protool.com/reach
11 Warranty
For our tools, we give warranty for material and
production defects in accordance with the locally
applicable legal provisions, but in any case for at
least 12 months. Within the EU member states, the
warranty period is 24 months (verifi cation through
invoice or delivery note).
Damage caused by, in particular, natural wear,
overloading, incorrect handling, or damage caused
by the operator, or damage caused through use of
the equipment contrary that specifi ed in the Oper-
ating Instructions, or damage which was known at
the time of purchase, is not covered by the war-
ranty. Furthermore, damage caused by the use of
non-original PROTOOL accessories and consumable
material (e.g. sanding pads) is also excluded.
Complaints can only be recognised if the tool is
returned while still assembled to the supplier or an
authorised PROTOOL Customer Service workshop.
Keep the Operating Instructions, Safety Instruc-
tions, Spare Parts List and purchase receipt in a
safe place. Otherwise the respective, current war-
ranty condi tions of the manufacturer shall apply.
Note
Due to continuous research and development work,
we reserve the right to make changes to the tech-
nical content of this documentation.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool WCP50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool WCP50 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info