490697

Protool SSP 200 EB Manual

29
Zoom out
Zoom in
Previous page
1/182
Next page
29
14 Declaration of Conformity
Sword saw Serial no.
SSP 200 EB 638557
We declare under our sole responsibility that this
product is in conformity with the following stand-
ards or standardization documents:
E N 55 0 14 -1 , E N 55 014-2, E N 6 0 745-1, EN 60 745 -2-1 3,
EN 61 000-3-2, EN 61 000-3-3 according to the
provision of the regulations stipulated in Directive
2006/42/EC, 2004/108/EC, 2000/14/EC.
All the procedures were applied as validly amended
at the time of the issue of this declaration, without
quoting these.
Technical documentation is kept at the manufac-
turer.
11
Stanislav Jakeš
Research and development
Protool GmbH
Wertstr. 20
D-73240 Wendlingen
31. 1. 2011
15 Service
Any repairs during and after the warranty period shall be performed by the service centres listed.
15.1 Troubleshooting
Problem Cause Solution
The machine will not run No power supply Check the safety fuses and the
power cords
Worn brushes Replace the brushes
Stuck switch Press the unblocking button
When overloaded Check the safety fuses
The cut is not clean; the chain
goes to the side
Moves into cut too far Reduce the movement
Blunt tool Sharpen the chain or replace it
with a new one
The chain is not sharpened
properly
Replace the chain with a new
one
Strong force required to move
the machine into the cut
The supporting area of the runner
is dirty
Clean it
Blunt tool Sharpen the chain or replace it
with a new one
Different qualities of wood Adjust the size of the movement
into the cut
Moves into cut too far Reduce the movement
The chain is not lubricated Blocked lubrication grooves on the
guide bar
Clean the guide bar
Defective oil feed pump Replace the pump (at an
authorised service centre)
Empty oil reservoir Replenish chain oil
The machine’s inner oil channels
are clogged or the bio oil has
solidifi ed
Clean the machine (at an
authorised service centre)
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool SSP 200 EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool SSP 200 EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info