490679

Protool RGP130 Manual

17
Zoom out
Zoom in
Previous page
1/132
Next page
17
► Make yourself sure whether the material
that is going to be machined does not
contain electric, water or gas lines – an
injury could occur.
► Do not grind metal surfaces, nails or
screws.
► The machine is not allowed to be operat-
ed by a person under 16 years of age.
5.8 Noise / Vibration Information
CAUTION
The noise created during work may
damage hearing.
► Use hearing-protective aids!
Measured values determined according to
EN 60 745.
Typically the A-weighted noise level of the
tool are:
Sound pressure level: 89 dB (A).
Sound power level: 100 dB (A).
Inaccuracy of measurement K = 3 dB (A).
The typical weighted acceleration is 5 m/s
2
.
Inaccuracy of measurement K = 1.5 m/s
2
.
6 Activation
WARNING
Risk of injury, if the tools are used
with wrong supply power.
Check that the information on the manufac-
turing label complies with the actual power
supply voltage.
Check that the plug type is the same as the
socket type.
Tools designed for 230 V may be connected
to 220 V / 240 V power supply.
6.1 Switching on – off
Push the arresting lever [1-2] upfront which
results in releasing the switch lever [1-1].
Press the switch lever [1-1] and the ma-
chine will start up and releasing the button
will stop the machine.
Permanent operation
Push the arresting lever [1-2] upfront which
results in releasing the switch lever [1-1].
Concurrently push the switch lever [1-1] and
push the arresting lever [1-2] upfront. Re-
leasing the permanent operation is achieved
by repeated pressing and releasing of the
switch lever [1-1].
6.2 Regulation electronics
Starting current limitation
Electronically controlled continual running
secures device acceleration without back
thrust. Due to starting current limitation in
the device, 16 A protection is suffi cient.
Electronic revolutions pre-setting
Use the revolutions regulator [1-4] for
smooth revolutions pre-setting:
Level 1: 3000 min
–1
Level 4: 5800 min
–1
Level 2: 4000 min
–1
Level 5: 6700 min
–1
Level 3: 5000 min
–1
Level 6: 7700 min
–1
Required number of revolutions depends on
applied grinding wheel and worked mate-
rial.
Switching off during back thrust
During sudden drop of revolutions under
extreme load, the current input in motor
stops. For re-starting, the device must be
fi rst switched off and again switched on.
Protection against re-starting
Prevents the uncontrolled starting of the
device after current supply cut off. For re-
starting, the device must be fi rst switched
off and again switched on.
Constant electronics
Constant electronics maintains the number
of revolutions during idle operation and un-
der load to the same value; it guarantees a
constant working shift and balanced stock
removal.
Heat protection during overloading
The safety electronics switches the motor
cooling regime when the critical tempera-
ture is reached in order to protect it from
overheating under permanent extreme
load. The machine cannot be loaded, it runs
on reduced rpm. After cooling in approx
3 – 5 min, the machine is fully loadable.
Heat protection for devices heated during
operation, reacts adequately sooner.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool RGP130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool RGP130 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info