Manual Protool MXP 1202 (page 12 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490694

Zoom out

Zoom in

1/88

6 Starting up and using the

machine

Check that the information on the manufacturing

label complies with the actual power supply volt-

age.

Check that the plug type is the same as the socket

type.

6.1 Tightening the stirrer

(see Fig. [2])

Screw in the stirrer [2-4] with endpiece M14x2

(wrench size 22) by turning it to the right in the

adapter ErgoFix [2-1] (wrench size 19) and use

the wrench to tighten it.

Fasten the ErgoFix adapter to the stirrer bar, then

insert the assembled stirrer into the slot of the

spindle. To set-up the working height see chap-

ter 6.5.

6.2 Switching the machine on and off

► Always hold the machine with both hands.

Pressing the switch [1-3] puts the machine into

operation and taking your hand away from the

switch stops the machine from working.

Using the switch button to control the speed

(acceleration function switch)

You can use the switch [1-3] to change the level

of the speed until it reaches the speed range that

is set by the speed controller.

Continuous operation

By pressing the switch [1-3] as far as it goes and

pressing the locking switch button [1-4] at the

same time, you can activate continuous operation.

Press and release the switch button [1-3] again to

switch off continuous operation.

6.3 Control electronics

Limiting the starting current

The electronically-controlled soft start ensures that

the machine starts up smoothly.

At the same time, this also prevents the materi-

als to be stirred from spurting out of the mixing

container. Thanks to the low starting current of the

machine, a 10 A fuse is sufﬁ cient.

Electronic speed preselection

You can use the speed controller [1-5] to set the

speed:

1st speed 2nd speed

Level 1 150 Level 1 300

Level 2 180 Level 2 370

Level 3 210 Level 3 440

Level 4 240 Level 4 510

Level 5 270 Level 5 580

Level 6 300 Level 6 650

The speed depends on the stirrer rod that is used

and on the material that you want to process.

Overload protection

An electronic overload protection protects the mo-

tor from damage if there is an extreme overload.

In this case, the motor remains at a standstill and

only starts up again once the load has been re-

moved. To restart the machine, you must switch

it on again.

Constant Electronic function

The Constant Electronic function maintains an al-

most constant speed and load; this ensures that

the material is stirred evenly.

Temperature-dependent overload protection

To protect the machine against overheating if you

are using it for an extremely prolonged period,

switch the safety electronics to the cooling mode

as soon as the critical temperature is reached. You

cannot load the machine and it runs at a reduced

speed. Approx. 2 minutes after cooling, the ma-

chine is again ready for use and fully able to take

loads.

Protection against re-starting

Prevents the uncontrolled starting of the device

after current supply cut off. For re-starting, the de-

vice must be ﬁ rst switched off and again switched

on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool MXP 1202 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool MXP 1202 Manual

Product: