Manual Protool ISP 330 EB (page 26 of 182) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490698

Zoom out

Zoom in

1/182

tion and prevent an unwanted start-up. When the

machine is turned off, an electric brake activates

and signiﬁ cantly shortens the run-down time of

the chain.

Do not remove the machine from the cutting piece

until the chain is at a standstill.

9.2 Controlling chain and guide bar

lubrication

The quantity of lubricating oil can be controlled

using a feed pump [5-2]. When you press the feed

pump, [5-2] the 0, 1, 2 and MAX positions can be

set at a notch [5-1]. Position 0 ensures minimum

lubrication for clean cuts, but must not be used

permanently, and after such cuts the chain and

plate must be lubricated with an increased quan-

tity. For permanent operation the quantity should

be set to level 2 and MAX.

9.3 Cut indicator

When cutting without the guide rail, adjust the

chain’s internal cutting plane using all of the indi-

cators on the guide runner:

- Indicator 0° [4-1] for rectangular cuts

- For bevel cuts:

• indicator 45° [4-4]

• indicator 60° [4-5]

To determine the chain’s external cutting plane,

use cutting proﬁ le indicators [4-6].

For cutting with the guide rail (GRP 800/1400/

3000-2; Fig. [8]), adjust the chain’s inner cutting

plane using only cut indicator 0° [4-1].

9.4 Guide ruler

Slide the guide ruler [1-3] into the holders in the

runner [1-6] and secure it with the hand screws

[1-5]. The guide ruler allows parallel cuts along

an even edge.

9.5 Exhaust

CAUTION

Inhaled dust may damage respiratory organs.

► During dusty jobs, wear a respiratory mask

and have the machine connected to exhaust

equipment.

To exhaust sawdust or dust, ordinary vacuum clean-

er suction hoses can be connected to the opening

of the rotary exhaust adaptor [1-10].

10 Using accessories

On the bottom part of the suction runner, the ma-

chine has a longitudinal groove for mounting on

the guide rail. Thus larger dimensions can be made

more easily and more precisely.

10.1 The PROTOOL guide system

When cutting larger work pieces, and to achieve ac-

curate angled cuts, use of the GRP 800/1400/3000-2

guide system is recommended for easy and safe

handling.

This allows clean cuts by accurately guiding the

machine along a marked edge. Hard anodising of

the guide bar makes moving the machine even

easier, thus reducing the necessary slide force,

and at the same time makes for a better working

procedure. The saw runner’s side clearance can be

adjusted using the distance screws in the auxiliary

handles [6-1].

10.2 Assembling the guide rail

(GRP 800/1400/3000-2)

The guide rail [7-1] is assembled using special

clamps CL-GRP 300 [7-2] or GRP-Rapid/L [7-5]

to be inserted into the guide grooves designed for

this particular purpose (Fig. [7a]). This allows a

secure hold on uneven surfaces. Anti-slip strips are

attached to the bottom of the guide bar, providing

safe placement and preventing scratches to the

material surface.

CAUTION

If you cut with a tilted saw, the tool and the

clamp bolt with the gripper or with GRP-Rapid/L

may collide.

► Tilt the saw at such an angle only to avoid

collision of the chain with the clamp.

10.3 Assembling the angle guide

(GRP-AG-2)

The combination of the guide rail and the continu-

ously adjustable angle unit [7-3] allows accurate

angular cuts, e. g., for matching ﬁ ts. Mount the

angle unit as shown in Fig. [7b]. You can set the

required cutting angle on the bevel indicator.

10.4 Assembling the connector

(CN-GRP)

Depending on the use and size of the work piece,

multiple guide rails can be jointed together us-

ing a connecting spring [7-4] (Fig. [7c]). For ﬁ rm

connection of multiple guide rails the links can be

afﬁ xed using the screws in the correspondingly

threaded openings.

10.5 Assembling the quick clamp

(GRP-Rapid/L)

The guide rail can be mounted quickly using this

device [7-5] slipped into the bottom groove. A ﬁ rm

mount is achieved by pressing the trigger, and re-

lease is achieved by pressing the stopping but-

ton.

CAUTION

If you cut with the saw at an incline, the tool and

the quick clamp handle may collide.

► The handle of the quick clamp must be turned

to the left towards the material after tighten-

ing, thus preventing the collision even at the

maximum tilt of 60°.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool ISP 330 EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool ISP 330 EB Manual

Product: