Manual Protector WA-5 (page 11 of 28) (English, German, Dutch, French)

738861

Zoom out

Zoom in

1/28

ENGLISH | WA-5

RECEIVER

using the pliers. Alternatively the wires can also be

soldered to the cable lugs.

SETTINGS

Function selector switch (11)

Use this selector switch to set whether a connected

device is to be switched ON or OFF. Slide the switch

to the OFF setting (crossed out socket) in order to

switch a connected device off if the sensor elec-

trodes (9) come into contact with water. The water

detector switches the connected device on when the

selector is set to ON.

Alarm volume switch (10)

Use this switch to set the volume of the alarm to

one of 3 levels. MAX is the highest setting and MIN

is the lowest setting.

RESET button (3)

Press the RESET button brieﬂy in order to cancel the

alarm after water has been detected.

MALFUNCTION

Alarm cannot be switched off using the

RESET button

If it is not possible to deactivate the alarm using

this button then it is still detecting water. This can

happen, for example, if water has penetrated the

sensor. In this event remove the water detector

from the socket and allow the sensor to dry. You

can also dismantle the sensor and then dry it with

a dry cloth.

electrodes (9) brieﬂy in tap water. If no alarm

sounds see the section ‘malfunction’.

MOUNTING

The sensor can be opened by removing the screw

(7). There is a small hole (13) on the back of the

sensor so that the sensor can be mounted at its

location using a small screw. You should select the

mounting location in such a way that any water can

be detected as quickly as possible. The two sensor

electrodes (9) should be just above the ﬂoor.

Adjusting the sensor cable (ﬁgures 2 + 3)

NOTE: disconnect the water detector from the

socket before shortening the cable.

If the sensor cable is too long then you can shorten

the cable as necessary. To do this you will need the

supplied ring cable lug, a small Philips screwdriver

and pliers (e.g. combination pliers).

First remove the casing screw (7) using the

screwdriver and remove the lid from the sensor. The

two electrode screws are now exposed and you can

remove these also. Caution, the electrodes are then

also released.

Use the pliers to shorten the cable and ensure that

you do not cut too much off. Remove the outer insu-

lation at the point of cutting to a length of approx.

15 mm and the insulation on the wires to approx.

5 mm, measured from the cut point. Push a ring

cable lug onto one of the two exposed wires and

then pinch the back of the ring cable lug together

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protector WA-5 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protector WA-5 Manual

Product: