657765
34
Zoom out
Zoom in
Previous page
1/72
Next page
34
LAUFRÄDER
Nehmen Sie zum Aufpumpen zuerst die Ventilkappe
1
(Abb.
AS) ab und verwenden Sie eine zum Fahrradventil passende
Luftpumpe. Bei Sclaverandventilen ist zu beachten, dass so-
wohl zum Aufpumpen als auch zum Luft ablassen, zusätzlich
noch eine kleine Rendelmutter
2
(Abb. AS) gelöst und mit
dem Finger kurz von oben angetippt werden muss. Nach dem
Pumpvorgang muss die Sicherungsmutter
2
(Abb. AS) wieder
zugedreht und die Ventilkappe
1
(Abb. AS) aufgesetzt werden.
VORDERRAD
VORDERRAD AUSBAUEN
1. Hängen Sie den Bremszug
1
(Abb. AT) aus.
2. Ziehen Sie, falls vorhanden, das Nabendynamokabel von
der Steckverbindung ab.
3. Lösen Sie die Achsmuttern, die den festen Sitz des Vorder-
rades gewährleisten, mit einem 15-mm-Schlüssel. Bei Mo-
dellen mit Schnellspanner lösen Sie den Hebel des Schnell-
spanners (s. auch Kapitel Schnellspanner).
4. Nehmen Sie die Muttern samt Unterlegscheiben von der
Achse ab.
5. Ziehen Sie das Vorderrad aus der Achsaufnahme heraus.
VORDERRAD EINBAUEN
1. Setzen Sie das Vorderrad mit dem Nabendynamokabel (falls vorhanden) auf der rechten Seite
gerade in die Achsaufnahme.
2. Stecken Sie die Unterlegscheiben und Muttern auf die Achse.
3. Ziehen Sie die Achsmuttern mit einem 15-mm-Schlüssel gemäß der Drehmomentvorgabe fest
an. Bei Modellen mit Achsschnellspanner schließen Sie den Schnellspannhebel (s. auch Kapi-
tel Schnellspanner).
4. Stecken Sie das Nabendynamokabel in die Steckbuchse (falls vorhanden).
5. Hängen Sie den Bremszug
1
(Abb. AT) wieder ein.
6. Prüfen Sie, ob die V-Brake-Bremse ordnungsgemäß funktioniert. Stellen Sie sie gegebenen-
falls neu ein (s. Kapitel Bremse).
Bei nicht korrekt eingebauten Laufrädern kann das Brems- und Fahrverhalten negativ
beeinträchtigt werden. Unfallgefahr!
Ziehen Sie alle zuvor gelösten Schrauben und Muttern wieder fest an. Das
Vorderrad kann sich sonst während der Fahrt lösen! Führen Sie nach dem Einbau vor-
sichtig eine Testfahrt durch. Unfallgefahr!
GEFAHR
1
2
AS
1
2
AT
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Prophete-REX Retro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Prophete-REX Retro in the language / languages: German as an attachment in your email.

The manual is 3,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info