527013
20
Zoom out
Zoom in
Previous page
1/42
Next page
20
English
Connection
1. Connect a red wire on the + bolt and a black
wire on the – bolt of the charger by means
of a M6 terminal ring.
2. Fasten firstly the other side of the red cable
on the + pole of the battery (with an alligator
clip, battery clamp or terminal ring). Repeat
this with the black wire on the - pole of the battery.
3. The power plug can be put into a socket. The charging
process will begin.
When you want to disconnect the charger from the battery, the power plug must be
removed from the outlet firstly.
Important
The battery junction that isn’t linked with the frame should be connected firstly.
The other junction must be made with the frame.
The connection between the charger and the battery must be made some distance
from the fuel installation.
Check whether the mains voltage of the voltage source is the same as the required
input voltage of the charger
It is also very important that you observe the following procedures:
Always use the screw nuts and washers (brass nickel) included. When other materials
are used there is a risk that the bolt will burn out of the print board.
Make sure that the wires make good contact between the charger and the battery. If
this connection is weak, there is a chance that the bolts will burn out of the print
board.
Do not tighten the screws more than necessary. If the screws are tightened too much
the bolts may disconnect from the print board.
If the charger has a malfunction because these procedures are not observed, the
warranty will lapse.
CO N NE CT ING A BA TT ERY IS OLATO R
You can charge/maintain two or three battery sets simultaneously by using a battery
isolater. It is important to connect the D+ connector of the charger. If the D+ connector
is not connected then the system will not work. Connect the D+ connection on the
charger with the D+ connection on the battery separator by means of a thin cable (+/-
1.5mmq). In addition, mount a diode between the D+ of the dynamo and the D+ battery
isolator. We advise you to use the low-loss DB 180 (2 outputs) or the DB 270 (3
outputs).
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proosten TBC 600 1-KANAALS - Software V1.3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proosten TBC 600 1-KANAALS - Software V1.3 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info