527014
15
Zoom out
Zoom in
Previous page
1/43
Next page
English

Charge time monitoring
When the charger is set for a ‘stand alone’ application, the duration of the charging
process is monitored. If the boost and equalize phase together take more than 14 hours,
the charging process will be stopped. This way it can be prevented a broken battery will
be charged continuously. But with this feature it also can become clear that the charge
current isn’t in the correct proportion to the battery capacity (the battery can become
damaged when the charge process takes too long).
Voltage drop compensation
The battery charger automatically compensates for the voltage drop over the connection
cables. Because of this, it’s possible that a voltage reading on the connection terminals
will be higher than the set value. The correct current can therefore only be measured
through the battery poles.
Soft start
The Promax 200 features a soft start, so that the charger has no influence on any power
users which may be turned on (such as lighting for example). Because of this the correct
charge level can only be indicated 3 min after start-up.
Temperature
The Promax 200 is protected against excess temperatures. At an internal temperature of
more than 40ºC the fan will turn on automatically. When the internal temperature is
cooled down until 35ºC, the fan also stops automatically. If the cooling of the fan isn’t
enough the charger will shut down totally. This thermal stop is indicated by an error
indication. When the charger has cooled down until 100ºC it will continue the charging
process. How the temperature protective devices operate will depend strongly on the
ambient temperature.
Level of protection
The indication for the degree of protection contains the character ‘IP’ (International
Protection) followed by two or three digits that stipulates the conditions that it complies
with. The first digit refers to the class of protection for density, the second digit to the
fluid density and the last digit refers to the impact resistance. The Promax 200 can be
assigned IP 205, which means:
2 = the charger is protected against solid particulate larger than 12mm.
0 = the charger is not protected against water/liquid etc.
5 = the charger can bear a n impact force of 2.00 Joule (2Nm) max.
Important
Protect the charger against moisture, pollution etc. This can be sucked in by the fan en
will damage the charger internally. The cost for this repair is not covered by warranty.
SETTING THE CHARGING PROGRAM
The charging program can be set by pressing the mode’ pushbutton on the front of the
charger. Set the ProMax 200 to the correct program before mounting the case. The
battery may be connected already but this is not a requirement.
The set up of the charger consists out of three phases.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proosten ProMax 200 - Software V1.3.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proosten ProMax 200 - Software V1.3.1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info