701850

Proklima FN-114509.1 Manual

42
Zoom out
Zoom in
Previous page
1/84
Next page
- 41 -
4) Line up the holes and fit the bolt all the way through. (fig. 4)
5) Fit the nut to the protruding end of the bolt and using a spanner and a screw driver, tighten the nut. (fig. 5)
6) Repeat for the other two legs.
7) To open out the legs, grasp a leg whilst holding the hub firmly and swing the leg out until it locks in place.
(fig. 6)
8) Adujust the height adjustment pipe to your desired height and tighten the fastening knob. (fig. 7)
CAUTION: Take care not to pinch your hand or any other object in the hinged components.
2. Motor housing assembly
1) Stand the Tripod on the floor.
2) Remove the big black knob and mounting bolt from the top of the adjustment pipe. Unscrew the knob and
pull the bolt straight out. (fig. 8)
3) Loosen the small screw from the bracket on the motor housing. (fig. 9)
4) Find the hole in the adjustment pipe which is pointed out by the arrow. (fig. 10)
5) Sit Motor housing on top of the adjustment pipe ensuring the small screw on the motor bracket lines up
with the hole in the pipe, then tighten the screw all the way in. (fig. 11)
6) Insert the mounting bolt through the bracket and the pipe. Note: the Square section under the head of the
bolt must be aligned with the square hole in the bracket (fig. 12)
7) Refit the big black knob to the mounting bolt. (fig. 13)
8) Screw in the small black knob but do not tighten. (fig. 14)
9) Adjust the tilt angle of the fan head to your desired position and then fully tighten both the small and big
black knobs.
3. Fan guards and blade assembly
1) To assemble the fan guards and blade, first remove the 4 rear guard fastening screws from the motor. (fig.
15)
2) Fit the rear guard into position (with the handle on the back of the guard at the top) and refit the 4 screws
and tighten. (fig. 16)
3) Remove the protective plastic sleeve from the motor spindle shaft and discard.
4) Next, rotate the motor spindle until the area with the “flat” surface is facing up.
5) Slide the fan blade onto the spindle ensuring the screw is lined up with the “flat” surface on the spindle as
shown. (fig. 17)
6) Push on until the end of the spindle is flush with the end of the fan blade hole, then tighten the screw. (fig.
18)
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proklima FN-114509.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proklima FN-114509.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info