Manual Progress PAG6430E-N (page 22 of 52) (English, German, Dutch, French)

574247

Zoom out

Zoom in

1/52

Important! Make sure that the gas supply

pressure of the appliance obeys the

recommended values. The adjustable

connection is fixed to the comprehensive

ramp by means of a threaded nut G 1/2"

(NEN 3258). Screw the parts and tighten

everything with teflon tape, if necessary, to

get the right direction.

ABC

A) End of shaft with nut

B) Washer

C) Elbow

Liquid gas

Use the rubber pipe holder for liquid gas.

Always engage the gasket. Then continue

with the gas connection.

The flexible pipe is prepared for apply

when:

– it can not get hot more than room tem-

perature, higher than 30°C;

– it is no longer than 1500 mm;

– it shows no throttles;

– it is not subject to traction or torsion;

– it does not get in touch with cutting

edges or corners;

– it can be easily examined in order to

make sure its condition.

The control of preservation of the flexible

pipe consists in checking that:

– it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

– the material is not hardened, but shows

its correct elasticity;

– the fastening clamps are not rusted;

– expired term is not due.

If one or more defects are visible, do not re-

pair the pipe, but replace it.

Important! When installation is complete,

make sure that the seal of each pipe fitting

is correct. Use a soapy solution, not a

flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the in-

jectors and replace them with the ones

which are necessary for the type of gas

you use (see table in "Technical Infor-

mation" chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied with

the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you

must fit an applicable pressure adjuster on

the gas supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum posi-

tion.

3. Remove the knob.

4. With a thin screwdriver, adjust the by-

pass screw position.

A) The by-pass screw

• If you change from natural gas G25 25

mbar to liquid gas, fully tighten the ad-

justment screw in.

• If you change from liquid gas to natural

gas G25 25 mbar, undo the by-pass

screw approximately 1/4 of a turn (1/2 of

a turn for Triple Crown burner).

Warning! Make sure the flame does

not go out when you quickly turn the

knob from the maximum position to the

minimum position.

22 progress

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Progress PAG6430E-N in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Progress PAG6430E-N Manual

Product: