567092
7
Zoom out
Zoom in
Previous page
1/18
Next page
LAMP WITH ENERGY-SAVING LIGHT EN - 1
PLI-134 / PLI-137 / PLI-139
Le agradecemos la compra de este producto Profile.
Atención: Es importante que lea atentamente este
manual antes de utilizar el producto. Conserve bien
este manual.
Note
Check if building regulations apply to your area
whereby you must have the lamp installed by an
accredited electrician. An electrician can give you
information about correct wiring. Never install the fitting
outside in rainy weather.
SWITCH OFF THE POWER BEFORE YOU INSTALL
THE LAMP.
Correct installation
With installation outside preferably choose a place
under a roof.
Connect the lamp to a circuit with wall switch.
Unscrew the stainless steel bolts on the side to take
the holder from the fitting.
Fix the holder to the wall with 2 screws.
Fix the lamp back on the assembled holder.
Remove the cover of the cable connection.
Pull the power supply wires through the opening with
the rubber packing.
The lamp must be connected to mains voltage of
230V, max. fusing 16A.
Connect the wires according to figures 1 and 2.
Screw the cable connection cover tight again.
Always respect the instructions on the identification
label of the connected power cables.
Other uses than described above can cause damage
to the product and increase the risk of short-circuit,
fire, electric shocks, etc.
Fig.1
Fig. 2
The product may not be adapted as a whole. The
safety instructions must be strictly observed.
Safety instructions
The importer accepts no responsibility for damage
claims with respect to objects or persons that result
from incorrect use or non-compliance with the safety
instructions. Any damage claims in such cases will
be declared null and void.
When replacing the R7S 24W energy-saving light the
power supply must be switched off. Do not exceed
the maximum wattage of 24W.
Always replace cracked or broken glass by glass
with the same properties as the original glass.
Technical information
Working voltage: 230V AC (50/60 Hz)
Maximum lamp power: 24W
Maximum current strength: 10/16A
Dustproof and splashproof: IP44.
Passive infrared sensor (PIR)
Sensor angle: 120°
Sensor range: 10 metres at with 25°C.
Lighting time: +/- 5 sec. – 10 min.
Setting the functions
1) Setting the light intensity (lux)
With the LUX Switch you adjust the working of the
sensor to match the intensity of the ambient light.
If the arrow is pointing to the sun the sensor responds
in both daylight and at night.
If the arrow is pointing to the moon the sensor will only
respond at night.
In between the sensor responds in half-light.
2) Setting the lighting time (TIME)
With this adjusting knob you can set the period of the
light staying on after switching on. You can set the
time from 5 sec. to 10 min.
Continuous function
With this function you can allow the lamp to stay on
continuously (the sensor then no longer works).
To do this switch the switch the fitting is connected to
on and off for 1 second. The lamp will now stay on
continuously.
To switch off the continuous function switch the switch
the fitting is connected to off for 30 seconds and then
on again.
Maintenance
Only use a dry, soft cloth for cleaning the lamp.
Never immerse the lamp in water.
Maintenance and repairs may only be carried out by
technicians who are familiar with any applicable
regulations.
* L = phase
*
= earthing
* N = neutral wire
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PLI-137 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PLI-137 in the language / languages: Dutch as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info