814779

Proficare VL 3064 MS Manual

27
Zoom out
Zoom in
Previous page
1/46
Next page
English 27
Assembly instructions
The device must be completely assembled before initial
operation!
WARNING: Risk of injury!
The edges of the propeller are sharp. Use caution during
assembly.
NOTE:
• You will need a Phillips screwdriver of medium size for
the assembly.
• Screws not included as accessory are already pre-
installed at the respective parts.
• Also observe the “Overview of the Components” on
page 3.
1. Insert the pedestal tube into the base.
2. Place the weight and the washer at the bottom of the
base.
3. Tighten the offset screw by turning it clockwise.
4. Place the motor onto the pedestal tube according to Fig.
B. The square opening in the bracket must align with the
lower drill hole in the pedestal tube.
5. Insert the carriage bolt up to its square end stop into the
lower hole.
6. Use the small knurled thumbscrew and the limit bolt to
set the tilt angle of the fan.
7. Then attach the knurled nut to the end of the carriage
bolt and tighten.
8. Unscrew the 4 preassembled outer screws from the front
of the motor.
9. Hold the rear protective grid so that the 4 boreholes on
the protective grid are exactly above the 4 boreholes on
the motor.
NOTE:
Ensure that the carrying handle on the protective grid is
pointing upwards.
10. Mount the rear protective grid with the 4 screws.
11. Attach the propeller and fasten it with the locking screw.
CAUTION:
The screw must sit on the flattened side of the motor
shaft!
12. Attach the front protective grid by hanging the hook with
the nut into the rear protective grid.
NOTE:
Ensure that the holes on the grid edge for the fastening
screw in the front and rear protective grid are posi-
tioned above each other.
13. Close the fasteners on the circumference of the protec-
tive grid.
14. Secure the protective grid with the fastening screw and
the nut.
Position
The ideal position is a non-slip, flat surface.
Putting into Service
Electrical Connection
• Before inserting the plug into the socket. Make sure that
the mains voltage to be used matches that of the device.
You can find this information on the nameplate.
• Connect the device to a duly installed protective contact
socket.
Use
Basic Settings
Set the blower inclination angle before starting the device.
1. Unscrew the small knurled screw.
2. Tilt the protective grid into the desired position.
3. Re-tighten the knurled screw.
Height adjustment
1. Loosen the knurled thumbscrew of the pedestal tube.
2. Adjust the fan to the desired height.
3. Re-tighten the knurled screw.
Operation
To select the speed, use the rotary switch on the rear:
• 0 off
• I slow
• II medium
• III fast
To shut off the device, select the position 0.
Fan setting
You have two options:
Stationary
1. Shut off the device.
2. Pull the control knob upwards.
3. Use the carrying handle to place the device into the
desired position.
Oscillating
1. Shut off the device.
2. Press the control knob.
NOTE:
The device rotates automatically in the range of about
90 degrees.
3. To turn off the function, shut off the device and pull the
control knob upwards.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proficare VL 3064 MS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proficare VL 3064 MS in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info