789272

Probuilder 43637 Manual

26
Zoom out
Zoom in
Previous page
1/32
Next page
26
Angling the handle
Hold the release button (5) down and turn
the handle to the required angle from 0 to 90
degrees.
Let go of the release button and turn the
handle slightly until it clicks into the selected
position.
Use
Insert the required bit directly into the
screwdriver’s bit holder (1) or use the
magnetic holder as an extender between the
bit holder and bit.
Turn the torque selector to the required
setting. The higher the setting, the more
power used to screw the screw in.
Change the direction by pushing the switch
(8) to the right or left. If the switch is in the
middle position, the spindle is locked and
you can tighten or loosen screws by turning
the tool itself without it running.
Switch the screwdriver on and off using the
on/off button (5).
When the screwdriver is running, the work
light (10) automatically comes on.
Cleaning and maintenance
Wipe down using a well-wrung cloth after
use, and always keep the surface and
ventilation holes free of dirt.
Never use corrosive or abrasive detergents,
as these may aff ect the plastic parts of the
screwdriver.
If the screwdriver will not be used for a
prolonged period, fully charge it before
putting it away. Charge it at least once every
3 months to maintain the battery capacity.
Red and yellow light up:
The battery is partially charged.
Red only:
The battery must be charged before you can
continue using the screwdriver.
Do not use damaged or worn screw bits and
always select the correct type of bit for the
job.
Secure small items in a vice or similar. Never
hold the item in your hand!
Check for concealed power cables, pipes, etc.
in the items you are going to screw into. Do
not touch the plastic parts of the screwdriver
during use on masonry.
Make sure that the screw does not damage
any objects under or behind the item, e.g.
when screwing into walls.
Make sure the screwdriver has stopped
completely before changing direction.
Charging the battery
Charge the battery fully before using the
screwdriver for the � rst time.
Plug the adapter provided into the mains
socket and insert the charging connector
into the charging socket (6) on the
screwdriver.
A full charge takes 3-5 hours.
Never charge for more than 5 hours at a
time.
Unplug the adapter from the mains socket
after charging.
Checking the battery charging
status
Press the button (4) down and read off the
battery charging status on the LED battery
indicator.
Red, yellow and green light up:
Battery is fully charged.
Special safety requirements
Only charge the battery at room temperature
(max. 40° C).
Never charge the battery if the screwdriver,
adapter or cord is damaged.
Check that the ventilation slots on the
screwdriver are not blocked.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Probuilder 43637 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Probuilder 43637 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 14.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info