573702
4
Zoom out
Zoom in
Previous page
1/19
Next page
4
contact your vehicle’s manufacturer for vehicle specific wiring diagrams. Alternatively
you can just look for a 12V / 24V power supply.
6. The reverse light sockets on most vehicles have two wires
connected to them. Usually the negative wire is black and the
positive wire is a coloured wire. If you are uncertain about the
wiring, you can use a 12/24 volt multimeter available at most auto
parts stores to determine which is the positive wire. Follow the
manufacturer’s instructions for the safe use of the multimeter.
7. After determining which wire is the positive and which is the
negative, turn off the ignition key, then remove the battery’s
negative cable.
8. Connect the GREEN wire (TRIGGER for back camera) of the
monitor wireloom to reverse light’s positive(+)
9. Replace the reverse light bulb, and then re-install the light socket. Secure all the
wires with cable ties or electrical tape. This trigger cable has priority compared to
other trigger cables. When in reverse it shows always the back up camera.
10. Re-attach the negative battery cable to the battery.
11. Plug the camera to CAM-B (CAMERA BACK).
12. If LEFT/FRIGHT/FRONT cameras are optioned, please connect the trigger wire
according to above diagram. And plug the camera to each connector respectively.
Connect BROWN wire to e.g. brake trigger (+), and plug camera to CAM-F (CAMERA
FRONT)
Connect WHITE wire to e.g. left turning signal trigger (+), and plug camera to CAM-L
(CAMERA LEFT)
Connect BLUE wire to e.g. right turning signal trigger (+), and plug camera to CAM-R
(CAMERA RIGHT)
Monitor Installation
When choosing a location to mount the monitor, make sure the monitor is in an
area that will not obstruct your vision while driving.
The RVC7040N can be fixed in your vehicle on your dashboard or upside down on the
roof with the dashboard stand.
A. On Dashboard
1. Before mounting the monitor, clean the dashboard surface well.
2. Position the stand to the dashboard surface which suits your requirement.
3. Stick the double-side tape foam at the bottom of the stand. Alternatively screw in the
screws into the dashboard.
4. Press the stand against the dashboard surface to fix the location.
5. Snap in the monitor to the stand mounting arm.
6. Adjust the mounting arms to suit your view angle to the monitor.
On dashboard
On roof
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-User RVC7040N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-User RVC7040N in the language / languages: English, German as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info