573648

Pro-User RVC3620N Manual

4
Zoom out
Zoom in
Previous page
1/31
Next page
4
3. Mount the license plate on the license plate bracket.
4. Choose a routing path for the camera’s power cable through the vehicle’s (or trailer’s)
body to the reverse light circuit. If in doubt, seek professional installation assistance.
5. Some vehicles (or trailer) may have a hole available to pass the wire through, such as
where the license plate light is mounted, or you can drill a hole close to where the
power cable is attached to the camera. Once you have chosen where the cable will
enter the vehicle’s (or trailer’s) body, remove the camera. If you are able to use an
existing opening, skip the next two steps.
6. Before you drill a hole you MUST CHECK and see WHAT IS BEHIND WHERE YOU ARE
DRILLING. If there are any vehicle components, such as electrical parts or fuel
system components behind where you are drilling, you must take whatever
precaution is necessary not to damage them. Remove the license plate and camera
before drilling.
7. After you have drilled the hole, insert the supplied grommet, then pass the camera
cables through the grommet into the vehicle (or trailer’s). You must use the grommet
to prevent the metal edge of the hole from cutting the camera cable.
8. Mount the transmitter box inside the trunk. Connect the camera’s power cable and
the transmitter box power cable to the transmitter box.
NOTICE: Choose position to mount the transmitter boxes as close as possible to the
receiver for better signal transmission; The length of the power cables are long
enough for routing from the rear end to the front of the vehicle or trailer.
The transmitter doesn't comply with weatherproof.
9. Next you’ll need to find the vehicle’s (or trailer’s) reverse lights. Turn the vehicle’s
ignition key to the accessory position, engage the parking brake and put the car in
reverse. Look at the vehicle’s tail lights to see where the reverse lights are located,
they are the white lights. To locate the reverse light’s 12V+ wire it will be necessary
to gain access to the rear of the vehicle’s (or trailer’s) tail light. For help locating the
vehicle’s (or trailer’s) reverse light circuit contact your vehicle’s (or trailer’s)
manufacturer for vehicle specific wiring diagrams.
10. Once you have located the reverse light circuit you will have to route the transmitter
box power cable to that location. You must securely fasten the power cable to prevent
it from being caught on any vehicle component such as the trunk hinge. Never route
the cable on the outside of the vehicle (or trailer)!
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-User RVC3620N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-User RVC3620N in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info