Manual Pro-User DRC5040 (page 5 of 34) (English, German, Dutch, French)

807479

Zoom out

Zoom in

1/34

After choosing the method of mounting, follow these installation steps:

1) Choose a routing path for the camera’s power cable through the vehicle’s body to the reverse

light circuit. If in doubt, seek professional installation assistance.

2) Some vehicles may have a hole available to pass the wire through, such as where the license

plate light is mounted, or you can drill a hole close to where the power cable is attached to

the camera. Once you have chosen where the cable will enter the vehicle’s body, remove the

camera. If you are able to use an existing opening, skip the next two steps.

3) Before you drill a hole you must check and see what’s behind where you are drilling. If there

are any vehicle components, such as electrical parts or fuel system components behind where

you are drilling, you must take whatever precaution is necessary not to damage them.

Remove the license plate and camera before drilling.

4) After you have drilled the hole, insert the supplied grommet, then pass the camera cables

through the grommet into the vehicle. You must use the grommet to prevent the metal edge

of the hole from cutting the camera cable.

5) Next you’ll need to ﬁnd the vehicle’s reverse lights. Turn the vehicle’s ignition key to the

accessory position, engage the parking brake and put the car in reverse. Look at the vehicle’s

tail lights to see where the reverse lights are located, they are the white lights. To locate the

reverse light’s 12V/24V + wire it will be necessary to gain access to the rear of the vehicle’s

tail light. For help locating the vehicle’s reverse light circuit contact your vehicle’s

manufacturer for vehicle speciﬁc wiring diagrams.

6) Once you have located the reverse light circuit you will have to route the camera cable to

that location. You must securely fasten the power cable to prevent it from being caught on

any vehicle component such as the trunk hinge. Never route the cable on the outside of the

vehicle!

7) The reverse light sockets on most vehicles have two wires connected to them. Usually the

negative wire is black and the positive wire is a colored wire. If you are uncertain about the

wiring, you can use a 12V/24V multimeter available at most auto parts stores to determine

which is the positive wire. Follow the manufacturer’s instructions for the safe use of the

multimeter.

1 = Positive (+)

2 = Connector

3 = Lamp

4 = Negative (‐)

5 = Camera Negative (‐)

6 = Camera Positive (+)

7 = Camera

INSTALLATION

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pro-User DRC5040 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pro-User DRC5040 Manual

Product: