Manual Pro-User DRC-4310 (page 5 of 33) (English, German, Dutch, French)

573665

Zoom out

Zoom in

1/33

3. Mount the license plate on the license plate bracket.

4. Choose a routing path for the camera’s power cable through the vehicle’s body to the

reverse light circuit. If in doubt, seek professional installation assistance.

5. Some vehicles may have a hole available to pass the wire through, such as where the

license plate light is mounted, or you can drill a hole close to where the power cable

is attached to the camera. Once you have chosen where the cable will enter the

vehicle’s body, remove the camera. If you are able to use an existing opening, skip

the next two steps.

6. Before you drill a hole you MUST CHECK and see WHAT IS BEHIND WHERE YOU ARE

DRILLING. If there are any vehicle components, such as electrical parts or fuel

system components behind where you are drilling, you must take whatever

precaution is necessary not to damage them. Remove the license plate and camera

before drilling.

7. After you have drilled the hole, insert the supplied grommet, then pass the camera

cables through the grommet into the vehicle. You must use the grommet to prevent

the metal edge of the hole from cutting the camera cable.

8. Next you’ll need to find the vehicle’s reverse lights. Turn the vehicle’s ignition key to

the accessory position, engage the parking brake and put the car in reverse. Look at

the vehicle’s tail lights to see where the reverse lights are located, they are the white

lights. To locate the reverse light’s 12V/24V + wire it will be necessary to gain access

to the rear of the vehicle’s tail light. For help locating the vehicle’s reverse light circuit

contact your vehicle’s manufacturer for vehicle specific wiring diagrams.

9. Once you have located the reverse light circuit you will have to route the camera

cable to that location. You must securely fasten the power cable to prevent it from

being caught on any vehicle component such as the trunk hinge. Never route the

cable on the outside of the vehicle!

10. The reverse light sockets on most vehicles

have two wires connected to them.

Usually the negative wire is black and the

positive wire is a colored wire. If you are

uncertain about the wiring, you can use a

12V/24V multimeter available at most

auto parts stores to determine which is

the positive wire. Follow the

manufacturer’s instructions for the safe

use of the multimeter.

11. After determining which wire is the

positive and which is the negative, turn off the ignition key, then remove the

battery’s negative cable.

12. Splice the red wire using the supplied in-line wire connectors to the reverse light’s

positive (+) wire. Use a set of slip joint pliers to squeeze the TAP and insure good

connection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pro-User DRC-4310 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pro-User DRC-4310 Manual

Product: