553929
25
Zoom out
Zoom in
Previous page
1/36
Next page
25
TROUBLESHOOTING
Most treadmill problems can be solved by following
the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis-
tance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on
a. Make sure that the power cord is plugged into a
properly earthed outlet (see page 15). If an exten-
sion cord is needed, use only a 3-conductor, 14-
gauge (1 mm
2
) cord that is no longer than
5 ft. (1.5 m).
b. After the power cord has been plugged in, make
sure that the key is inserted into the console.
c. Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
powerswitch,waitforveminutesandthenpress
the switch back in.
SYMPTOM: The power turns off during use
a. Check the power switch (see the drawing above).
Iftheswitchhastripped,waitforveminutesand
then press the switch back in.
b. Make sure that the power cord is plugged in. If the
powercordispluggedin,unplugit,waitforve
minutes, and then plug it back in.
c. Remove the key from the console, and then
reinsert it.
d. If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The console displays remain lit when
you remove the key from the console
a. The console features a display demo mode, de-
signed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 23 to turn off the
demo mode.
SYMPTOM: The displays of the console do not
function properly
a. Remove the key from the console and UNPLUG
THE POWER CORD. Place the treadmill in
the storage position (see HOW TO FOLD THE
TREADMILL on page 24).
Next, remove the two indicated #8 x 3/4"
Screws (6).
Lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 24). Remove the
three #8 x 3/4" Screws (6). Carefully slide the Motor
Hood (57) off.
Reset
Tripped
c
6
6
a
57
6
6
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form 910 ZLT - PETL10812 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form 910 ZLT - PETL10812 in the language / languages: English as an attachment in your email.

The manual is 4,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form 910 ZLT - PETL10812

Pro-form 910 ZLT - PETL10812 User Manual - German - 36 pages

Pro-form 910 ZLT - PETL10812 User Manual - Dutch - 36 pages

Pro-form 910 ZLT - PETL10812 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info