Manual Pro-form 900 ZLT - PETL10810 (page 26 of 36) (English)

553937

26

Zoom out

Zoom in

Previous page

1/36

Next page

26

Remove the three #8 x 3/4" Screws (1) and care-

fully pivot the Motor Hood (62) off.

Locate the Reed Switch (73) and the Magnet (47)

on the left side of the Pulley (48). Turn the Pulley

until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and

the Reed Switch is about 1/8 in. (3 mm). If neces-

sary, loosen the #8 x 3/4" Truss Head Screw (18),

move the Reed Switch slightly, and then retighten

the Screw. Reattach the Motor Hood (not shown)

with the #8 x 3/4" Screws. Reattach the #8 x 2"

Screws if necessary. Run the treadmill for a few

minutes to check for a correct speed reading.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. Hold down the Stop button and the Speed increase button, insert the key into the console, and

then release the Stop button and the Speed increase button. Press the Stop button and then

press the Incline increase or decrease button. The treadmill will automatically rise to the maxi-

mum incline level and then return to the minimum level. This will recalibrate the incline system. If

the incline does not calibrate, press the Stop button again, and then press the Incline increase or

decrease button again. When the incline is calibrated, remove the key from the console.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 14-gauge (1 mm

2

) cord that is no longer

than 5 ft. (1.5 m).

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be-

come damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both

idler roller bolts counterclockwise, 1/4 of a turn.

When the walking belt is properly tightened, you

should be able to lift each edge of the walking belt 2

to 3 in. (5 to 7 cm) off the walking platform. Be care-

ful to keep the walking belt centered. Then, plug in

the power cord, insert the key, and run the treadmill

for a few minutes. Repeat until the walking belt is

properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

Top

View

47

18

73

1/8 in.

48

Idler Roller Bolts

2–3 in.

b

62

1

1

Bonjour,
Je vous contacte pour information car je rencontré une panne sur mon tapis 900 zlt.
Il a cessé de fonctionner après avoir fait disjoncté le tableau électrique.
Lors de la remiseen service le tableau s'allume mais des que l'on remet le tapis à tourner ça disjoncté cte à nouveau.
Avez-vous déjà rencontré ce problème ou pouvez-vous me renseigner sur la panne.
Cordialement
Benoit Submitted on 22-9-2021 at 18:27
Reply Report abuse
Bonjour,
Je vous contacte pour information car je rencontré une panne sur mon tapis 900 zlt.
Il a cessé de fonctionner après avoir fait disjoncté le tableau électrique.
Lors de la remise en service le tableau s'allume mais des que l'on remet le tapis à tourner ça disjoncté cte à nouveau.
Avez-vous déjà rencontré ce problème ou pouvez-vous me renseigner sur la panne.
Cordialement
Benoit Submitted on 22-9-2021 at 18:27
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Pro-form 900 ZLT - PETL10810 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form 900 ZLT - PETL10810 in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form 900 ZLT - PETL10810

Pro-form 900 ZLT - PETL10810 User Manual - German - 36 pages

Pro-form 900 ZLT - PETL10810 User Manual - Dutch - 36 pages

Pro-form 900 ZLT - PETL10810 User Manual - French - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info