708083
6
Zoom out
Zoom in
Previous page
1/36
Next page
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated
with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the
walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there
is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys, your own phillips screwdriver , and your
own rubber mallet .
For help identifying the assembly hardware, see the drawings below.
The number in parentheses below each
drawing is the key number of the part, from the PART LIST on pages 30 and 31. The number following the paren-
theses is the quantity needed for assembly.
Note: If a part is not in the parts bag, check to see if it has been
pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly.
3/4” Tek Screw (58)–8
1
Silver Ground
Screw (33)–1
1/4” Star Washer
(
H
W
Latch Screw
(XXX)–2
Handrail Bolt (20)–4
Extension Leg Bolt (64)–4
Star Washer (8)–8
Screw (3)–11
Handrail Bolt (50)–4
Handrail Bolt/Extension Leg Bolt (64)–8
1” Tek Screw
(22)–4
6
1. Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side as shown. Partially
fold the Frame (58) so the treadmill is more sta-
ble. Do not fully fold the treadmill until it is
completely assembled.
Insert an Extension Leg (89) into the base of the
Upright (84) as shown. Note: Be careful not to
pinch the Upright Wire Harness (77) in the
base of the Upright. To fully insert the
Extension Leg, it may be necessary to tap on it
with a mallet. Next, insert two Extension Leg
Bolts (64) with Star Washers (8) into the bottom
of the Extension Leg, and firmly tighten the
Extension Leg Bolts.
8
1
58
89
64
77
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form 480 CX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form 480 CX in the language / languages: English as an attachment in your email.

The manual is 3,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info