712201

Privileg PRC871 Manual

19
Zoom out
Zoom in
Previous page
1/44
Next page
19
Installation instructions for product with Hettich hinges
! It is recommended that this installation be performed by authorized technical stuff.
! Before installation, read the instructions carefully.
! Fit the refrigerator/freezer in stable kitchen units only.
! Cabinet dimensions are changed by material of trim flap
1
.
1. If material of trim flap
(1)
is plastic, look at (Table.1/B1) for cabinet dimensions.
2. If material of trim flap
(1)
is metal, look at (Table.1/B2) for cabinet dimensions.
! If necessary, reverse the door according to instructions.
1. See fig.A for the necessary attachment components.
2. Open the package. Take gasket spacer
(9)
and brake into three as shown in figureD. Themiddle
part is door hang rail
(10)
. The other two parts are unit door spacers
(11)
. (fig.D)
3. Insert trim flap
(1)
into slot and screw by screws
(8)
. (fig.E)
4. Pass the power cord through ventilation shaft and position it so that the appliance couldbe easily
plugged in once it has been installed. (fig.B - fig.C)
5. Cut trim gasket
(4)
to the height of the recess and stick it on reverse side of the doorhinges of
the appliance. (fig.E)
6. Raise the appliance and slide into the kitchen unit.
7. Lean the appliance to the kitchen unit through the hinges and align the front feet with
frontsurface of the kitchen unit. (fig.F)
8. Open the appliance door and screw the front feet by using screws
(7)
. (fig.G)
9. Screw trim flap
(1)
to kitchen unit using screws
(7)
. (fig.G)
10. Screw the hinges to the kitchen unit using screws
(7)
. (fig.G)
11. Close the appliance door. Unscrew and remove the nuts
(14)
, washers
(13)
and
adjustmentbolts
(12)
from the appliance door. (fig.H)
12. Take out the liners of the tapes on door hang rails
(10)
. Place door hang rails
(10)
on theappliance
door by inserting the bosses on the holes of the appliance door, aligning thefront surfaces of the
door hang rails(
10)
and the appliance door parallel to each other. Letthe door hang rails
(10)
,
stick onto the appliance door. (fig.H)
13. Slide the door hang
(2)
into door hang rails
(10)
. (fig.J - fig.K)
14. Take out the liners of the tapes on the front side of the door hang
(2)
.
15. Take out the liners of the tapes on the unit door spacers
(11)
and and stick them onto theunit
door(15), closer to the upper corners. (fig.K)
16. Lean the unit door
(15)
to the door hang
(2)
, aligning the unit door spacers(11) on the left,right
and top edges with the sides of the unit or the doors of the nearer and upper kitchenunits.
(fig.K)
17. Make sure that the unit door
(15)
sticks onto the door hang
(2)
. Pull the unit door
(15)
allowing the
door hang
(2)
to slide out the door hang rails
(10)
. Observe that the door hang
(2)
stays stuck on
the unit door
(15)
. (fig.L)
18. Lay down the unit door
(15)
on the floor and screw the door hang
(2)
to the unit door
(15)
by
screws
(7)
. (fig.L)
19. To overcome some of the furniture mistakes, there are plastic spacers
(A)
sticked on the door
hang
(2)
. Remove these plastic spacers
(A)
. (fig.M)
20. Remove the door hang rails
(10)
from the appliance door. Screw the adjustment bolts
(12)
to the
holes on the appliance door by leaving the necessary space using unit door spacer
(11)
. (fig.N)
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Privileg PRC871 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Privileg PRC871 in the language / languages: English, German as an attachment in your email.

The manual is 5,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info