Manual Privileg PRC551 (page 17 of 76) (English, German, Dutch, French)

712225

Zoom out

Zoom in

1/76

Installation instructions for product with Hettich hinges

! It is recommended that this installation be performed by authorized technical stuff.

! Before installation, read the instructions carefully.

! Fit the refrigerator/freezer in stable kitchen units only.

! Cabinet dimensions are changed by material of trim ap

1. If material of trim ap

(1)

is plastic, look at (Table.1/B1) for cabinet dimensions.

2. If material of trim ap

(1)

is metal, look at (Table.1/B2) for cabinet dimensions.

! If necessary, reverse the door according to instructions.

1. See g.A for the necessary attachment components.

2. Open the package. Take gasket spacer

(9)

and brake into three as shown in gureD.

Themiddle part is door hang rail

(10)

. The other two parts are unit door spacers

(11)

. (g.D)

3. Insert trim ap

(1)

into slot and screw by screws

(8)

. (g.E)

4. Pass the power cord through ventilation shaft and position it so that the appliance could-

be easily plugged in once it has been installed. (g.B - g.C)

5. Cut trim gasket

(4)

to the height of the recess and stick it on reverse side of the doorhin-

ges of the appliance. (g.E)

6. Raise the appliance and slide into the kitchen unit.

7. Lean the appliance to the kitchen unit through the hinges and align the front feet with

frontsurface of the kitchen unit. (g.F)

8. Open the appliance door and screw the front feet by using screws

(7)

. (g.G)

9. Screw trim ap

(1)

to kitchen unit using screws

(7)

. (g.G)

10. Screw the hinges to the kitchen unit using screws

(7)

. (g.G)

11. Close the appliance door. Unscrew and remove the nuts

(14)

, washers

(13)

and adjustmen-

tbolts

(12)

from the appliance door. (g.H)

12. Remove the liner for the adhesive part on the door hang rails

(10)

. Place door hang

rails

(10)

on theappliance door by inserting the bosses on the holes of the appliance door,

aligning thefront surfaces of the door hang rails(

10)

and the appliance door parallel to

each other. Letthe door hang rails

(10)

, stick onto the appliance door. (g.H)

13. Slide the door hang

(2)

into door hang rails

(10)

. (g.J - g.K)

14. Take out the liners of the adhesive part on the front side of the door hang

(2)

15. Take out the liners of the adhesive part on the unit door spacers

(11)

and and stick them

onto theunit door(15), closer to the upper corners. (g.K)

16. Lean the unit door

(15)

to the door hang

(2)

, aligning the unit door spacers(11) on the

left,right and top edges with the sides of the unit or the doors of the nearer and upper

kitchenunits. (g.K)

17. Make sure that the unit door

(15)

sticks onto the door hang

(2)

. Pull the unit door

(15)

al-

lowing the door hang

(2)

to slide out the door hang rails

(10)

. Observe that the door hang

(2)

stays stuck on the unit door

(15)

. (g.L)

18. Lay down the unit door

(15)

on the oor and screw the door hang

(2)

to the unit door

(15)

screws

(7)

. (g.L)

19. To overcome some of the furniture mistakes, there are plastic spacers

(A)

sticked on the

door hang

(2)

. Remove these plastic spacers

(A)

. (g.M)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Privileg PRC551 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 12,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Privileg PRC551 Manual

Product: