IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean
immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish o with a dry cloth.
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the enamel surface.
• Use detergents specically designed for cleaning the appliance and follow the manufacturer instructions.
IMPORTANT: clean the lters at least monthly to remove any oil or grease residuals.
MAINTENANCE
WARNING:
- use protective gloves.
- disconnect the appliance from the power supply.
GREASE FILTERS
The metal grease lter has an unlimited life and should be cleaned once a month by hand or in a dishwasher at low
temperature and with a short cycle. Cleaning in a dishwasher may cause discoloring of the grease lter, but its ltering
eciency is unaected.
Pull out the steam deector.
Pull out the handle to remove the lter.
Wash the lter and leave it to dry, proceeding in reverse order to ret
REPLACING LAMPS
IMPORTANT: check the type of lamp is suitable for your particular model of appliance.
Replace the lamp with an identical one as indicated on the specications label or next to the lamp itself, on
the hood
1.Disconnect the hood from the household mains.
2.Open the steam collecting drawer and remove the grease lters (see the section entitled “grease lters”).
3.Remove the damaged bulb and replace it with a new one.
Use E14 2,5W max LED lamps only. For more details, check enclosed leaet “ILCOS D” (alfanumeric position “1e”).
4.Ret the grease lters.
CARBON FILTER
It captures and neutralizes unwanted cooking odours.
Change the carbon lter every 4 months
Fitting or changing the carbon lter
1.Pull out the steam deector.
2.Remove all the grease lters (refer to the section “grease lters”).
3.Install the carbon lter covering the motor compartment.
Note: Proceed in reverse order to remove.
Proceed in reverse order to ret the grease lters in place.
MATERIAL SUPPLIED
• Hood assembled with motor, bulbs and grease lters tted.
• 1 instruction booklet
• 1 drilling template
• 1 cable clamp
• 1 screw (3.5 x 9.5)
• 1 power cable
• 2 brackets for adjusting the drawer’s end stop
• 2 washers
• 2 screws (3.5 x 5)
• 4 spacers
• 2 torx adapters
• 4 screws (4.5 x 16)
• 6 round adhesive labels
• 2 half valves
Please note: Carbon lter and fascia not supplied.
INSTALLATION - PRELIMINARY ASSEMBLY INSTRUCTIONS
The hood is designed for installation and use in “Extractor version” or in “Filter version”.
Extractor Version
Fumes are extracted and expelled to the outside through an exhaust pipe (not supplied) xed to the hood exhaust pipe connector.
Depending on the exhaust pipe purchased, provide for suitable xing to the exhaust pipe connector.
IMPORTANT: If already installed, remove the carbon lter/s.
Filter Version
Air is ltered through the carbon lter/s and recycled into the surrounding environment.
IMPORTANT: Check that air recirculation is ensured.
If the hood does not have the carbon lter/s, order one/them and t before use.
Install the hood away from very dirty areas, windows, doors and heat sources.
The hood comes with all the materials necessary for installation on the majority of walls/ceilings. However, a qualied technician must ensure that the materials are
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Privileg DGAH 66 LM X at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Privileg DGAH 66 LM X in the language / languages: English as an attachment in your email.
The manual is 0,74 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
