668245
14
Zoom out
Zoom in
Previous page
1/32
Next page
14 www.pridemobility.com Quantum 610 Series
V. COMFORT ADJUSTMENTS
COMFORT ADJUSTMENTS
After becoming familiar with your power chairs operation, you may nd the need to make some adjustments to
increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller
position. If your power chair is equipped with power positioning options, refer to the information supplied in
supplemental manuals or contact your Quantum Rehab Provider.
WARNING! The center of gravity of your power chair was factory set to a position that meets
the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated
your power chair and made any necessary adjustments to suit your speci c requirements. Do
not change your seating con guration without rst contacting your Quantum Rehab Provider.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to speci cations table for speci c component weights before you disassemble
the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort adjustments:
metric/standard socket set and ratchet
adjustable wrench
thread lock
Seat Height and Seat Angle Adjustment
You can change the seat height to one of four positions in
1-in. (2.54-cm) increments by raising the front and rear
trapeze bars. If you raise or lower only one trapeze bar (front
or rear), you can also change the seat base angle (dump).
To change the seat height:
1. Turn off the power to the controller.
2. Loosen the rear shroud fasteners and remove the rear
shroud. See gure 2.
3. Disconnect the controller connector(s) from the power
base. See gure 3.
4. Flip up the seat latch safety. See gure 11.
5. Squeeze the seat latch and release the seat from the front
trapeze bar. See gure 11.
6. Slide the seat forward and remove it from the power
base.
7. Loosen the screws that attach the trapeze bars to the seat
posts. See gure 12.
8. Remove the retaining clips that secure the seat posts to
the power base. See gure 12.
9. Move the trapeze bars up or down to the desired height.
10. Reinstall the retaining clips from step 8.
11. Remove each screw from the trapeze bars and apply
thread lock.
12. Reinstall each screw into the trapeze bars and tighten.
13. Reinstall the seat and ip down the seat latch safety.
14. Reconnect the controller connector(s) to the power base.
15. Reinstall the rear shroud and tighten the fasteners.
Figure 11. Seat Height Adjustment - Seat Latch
Safety
Figure 12. Seat Height Adjustment - Trapeze Bars
SCREWS
(2 OF 4)
TRAPEZE BARS
SEAT POSTS
(2 OF 4)
RETAINING
CLIPS
(2 OF 4)
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride QUANTUM 610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride QUANTUM 610 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info