668224
35
Zoom out
Zoom in
Previous page
1/44
Next page
35
Legend XL www.pridemobility.com
IX. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly
and easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed
below develops.
NOTE: Your scooter will not run unless the flash code condition is resolved and the scooter has been
turned off, then turned back on.
Flash Code Condition Solution
(1)
Battery voltage is too low to operate the
scooter or the charger is operating.
Charge batteries or unplug the charge power lead
from the electrical outlet.
(2) 
Motor disconnected Check all connections to the motor.
(3) 
Motor wiring fault Contact your authorized Pride Provider.
(6) 
Scooter is operating with the charger
attached.
Unplug the charger power lead from the charger
power lead receptacle.
(7) 
Throttle potentiometer fault Contact your authorized Pride Provider.
(8) 
Internal controller fault Contact your authorized Pride Provider.
(9) 
Brake fault - your scooter was left in
freewheel mode.
Turn the key to the “off position, then push the
manual freewheel lever to the drive (rearward)
position and restart your scooter.
(10) 
High battery voltage - The batteries
have been overcharged and the
scooter won’t run.
Leave the scooter turned on to drain the batteries
to a sufficient level. If the batteries continue to
overcharge, call your authorized Pride Provider.
What if all the systems on my scooter seem to be “dead”?
Make certain that the key is in the “on” position.
Check that the batteries are fully charged.
Push in the main circuit breaker reset button. See IV. “Your Scooter .”
Make certain that both T-handle battery harnesses are firmly connected to the rear section and to the battery
terminals. See VIII. “Disassembly and Assembly.”
Make sure that the front-to-rear harness is firmly connected to the rear section. See VIII. “Disassembly and
Assembly.”
Be sure the power down timer feature has not been activated. See V. “Batteries and Charging.”
Check the 3-amp fuse located on the lower portion of the tiller console. See X. “Care and Maintenance” for
fuse replacement.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Legend XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Legend XL in the language / languages: English as an attachment in your email.

The manual is 5,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pride Legend XL

Pride Legend XL User Manual - German - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info