721988

Pride Colt Twin Manual

38
Zoom out
Zoom in
Previous page
1/48
Next page
38
www.pridemobility.com Colt Twin
VIII. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
DIAGNOSTIC FAULT CODES
The diagnostic fault codes for your scooter are designed to help you perform basic troubleshooting quickly and
easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below
develops. Your scooter will also emit a beep code to indicate the system fault.
NOTE: Your scooter will not run unless the fault code condition is resolved and the scooter has been
turned off, then turned back on.
FAULT CODE CONDITION SOLUTION
! (1)
Battery charge is low. Charge batteries as soon as possible.
! ! (2)
Battery charge is too low to operate
the scooter.
Charge batteries.
! ! ! (3)
The scooter’s battery voltage is too
high to operate the scooter, or the
charger is still connected to charger
port.
Unplug charger and/or turn key off, then
back on again.
! ! ! ! (4)
Current limit time out.
T
urn the scooter off for a few minutes,
then turn your scooter back on.
! ! ! ! ! (5)
The manual freewheel lever is in the
(forward) freewheel position.
Remove the key from the key switch,
then push the manual freewheel lever to
the (rear) drive position, and restart your
scooter.
! ! ! ! ! ! (6)
Throttle control lever not at centre
position at start up.
Return the throttle control lever to centre
position, turn scooter off, and then back
on.
! ! ! ! ! ! ! (7)
Speed pot error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! (8)
Motor volts error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! ! (9)
Other internal errors.
Contact your authorised Pride Dealer for
assistance.
What if all the systems on my scooter seem to be dead?
! Make certain that the key is in the “on” position.
! Check that the batteries are fully charged.
! Push in the main circuit breaker reset button. See III. “Your Scooter.”
! Make certain that both battery harnesses and the front-to-rear harness are firmly connected. See VII. “Disas-
sembly and Assembly.”
! Be sure the power down timer feature has not been activated. See V. “Operation.”
What if my scooter does not move when I engage the throttle control lever?
! When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the motor/
transaxle assembly is cut.
! Push rearward on the manual freewheel lever, turn the scooter off and then turn the scooter on to return to
normal scooter operation.
… 38 …


Need help? Post your question in this forum.

Forumrules
1

Forum

pride-colt-twin

Reset search

  • On the colt twin pride do both batteries charge at the same time? When do I know both batteries are charged?
    Thanks Submitted on 15-3-2022 at 10:16

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Colt Twin at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Colt Twin in the language / languages: English as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info