722008
40
Zoom out
Zoom in
Previous page
1/48
Next page
40
www.pridemobility.com Colt Series
Follow these easy steps for a quick and safe repair
for solid tyres:
1. Remove the key from the key switch.
2. Elevate the side of the scooter of which you are
removing the tyre. Place wooden blocks under the
frame to elevate the scooter.
3. Remove the wheel cap, drive wheel nut and
washer from the axle. See figure 29.
4. Pull the wheel off of the axle.
5. Slide the new wheel onto the axle. Make sure the
the axle key is in the axle slot.
WARNING! Failure to ensure that the
axle key is properly installed into the
axle slot when mounting the wheel can
result in electronic brake failure,
personal injury and/or product damage.
6. Reinstall the drive wheel nut and washer onto the axle and tighten.
WARNING! Make sure that both the nut and washer are reinstalled and tightened
properly.
7. Reinstall the wheel cap.
8. Remove the blocks from beneath the scooter.
IX. CARE AND MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your
ability to perform the maintenance listed below, you may schedule inspection and maintenance at your
authorised Pride Dealer. The following areas require periodic inspection and/or care and maintenance.
TYRE PRESSURE
If equipped with pneumatic tyres, always maintain the psi/bar/kPa air pressure rating indicated on
each tyre.
WARNING! It is important that the psi/bar/kPa air pressure rating indicated on each tyre
be maintained in pneumatic tyres at all times. Do not underinflate or overinflate your
tyres. Low pressure may result in loss of control and overinflated tyres may burst. Failure
to maintain the psi/bar/kPa air pressure rating indicated on the tyres at all times may
result in tyre and/or wheel failure.
Regularly inspect your scooter’s tyres for signs of wear.
WHEEL REPLACEMENT
If your scooter is equipped with pneumatic tyres and you have a flat tyre, you can have the tube replaced. If your
scooter is equipped with a solid tyre insert, either the solid insert or the entire wheel must be replaced depending
on the model. Contact your authorised Pride Dealer for information regarding replacement wheels for your scooter.
WARNING! Be sure that the key is removed from the key switch and the scooter is not in
freewheel mode before performing this procedure repair.
WARNING! Completely deflate pneumatic tyres before dismantling the wheel or attempting
repair.
WARNING! When changing a tyre, remove only the centre lug nut, then remove the wheel. If
any further disassembly is required, deflate the tyre completely or it may explode.
WARNING! Wheels on your scooter should only be serviced/replaced by an authorised Pride
Dealer or qualified technician.
Figure 29. Solid Tyre Wheel Removal
AXLE
KEY
WASHER
DRIVE WHEEL NUT
WHEEL CAP
AXLE SLOT
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Colt Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Colt Series in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info