721986
37
Zoom out
Zoom in
Previous page
1/44
Next page
37
Colt Executive www.pridemobility.com
VIII. CARE AND MAINTENANCE
EXTERIOR SURFACES
Bumpers, tyres and trim can benefit from an occasional application of a rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tyre
tread, as this may cause them to become dangerously slippery.
CLEANING AND DISINFECTION
Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter.
Avoid using products that may scratch the surface of your scooter.
If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for
use on your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or
cleaning agent before applying it to your product. Failure to comply may result in skin
irritation or premature deterioration of upholstery and/or scooter finishes.
BATTERY TERMINAL CONNECTIONS
Make certain that the terminal connections remain tight and uncorroded.
The batteries must sit flat in the battery wells.
The battery terminals should face away from the seat post.
WIRING HARNESSES
Regularly check all wiring connections.
Regularly check all wiring insulation, including the charger power lead, for wear or damage.
Have your authorised Pride Dealer repair or replace any damaged connector, connection or insulation
that you find before using your scooter again.
PROHIBITED! Even though the scooter has passed the necessary testing requirements
for ingress of liquids, you should keep electrical connections away from sources of damp-
ness, including direct exposure to water or bodily fluids and incontinence. Check electri-
cal components frequently for signs of corrosion and replace as necessary.
WARNING! Do not pull on electrical harnesses directly to detach them from the
scooter. Always grasp the connector itself when disconnecting the harness to pre-
vent wire damage.
ABS PLASTIC SHROUDS
The front tiller shroud, front shroud and the rear shroud are formed from durable ABS plastic and are
coated with an advanced formula urethane paint.
A light application of car wax will help the shrouds retain their high gloss.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
These items are all prelubricated, sealed and require no subsequent lubrication.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodi-
cally for wear by your authorised Pride Dealer.
CONSOLE, CHARGER AND REAR ELECTRONICS
Keep these areas free of moisture.
Allow these areas to dry thoroughly if they have been exposed to moisture before operating your
scooter again.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Colt Executive at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Colt Executive in the language / languages: English as an attachment in your email.

The manual is 4,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info