721983
22
Zoom out
Zoom in
Previous page
1/40
Next page
22 www.pridemobility.com Athena
V. COMFORT ADJUSTMENTS
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to
increase your comfort such as controller position and anti-tip wheel height.
NOTE: If your power chair is equipped with a Synergy Seat or TRU-Balance Power Positioning System, refer
to the information provided in separate manuals.
WARNING! The centre of gravity of your power chair was factory set to a position that meets the
needs of the demographic majority of users. Your Quantum Rehab Dealer has evaluated your
power chair and made any necessary adjustments to suit your specific requirements. Do not
change your seating configuration without first contacting Pride Mobility Products Ltd. or your
Quantum Rehab Dealer.
WARNING! Your seat should only be installed or adjusted by a Quantum Rehab Dealer.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to “Appendix I - Specifications” for specific component weights before you
disassemble the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert,
resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or
through your Quantum Rehab Dealer.
You may need the following to make comfort adjustments:
metric/standard hex key set
metric/standard socket set and ratchet
adjustable wrench
Controller Position
You can position the controller for either left-hand or right-hand use. You can also adjust the extension of the
controller from the armrest.
WARNING! Do not place the controller harness so that it can be pinched in the seat frame or the
power base frame.
Figure 12. Adjusting Controller Position
SETSCREWS
MOUNTING SCREWS
MOUNTING BLOCK
To change the controller position:
1. Turn off the power to the controller.
2. Unplug the controller connector from the power base.
3. Remove any wire ties securing the controller harness to
the armrest.
4. Loosen the mounting screws in the controller mounting
block. See figure 12.
5. Move the controller mounting block and controller to
the other armrest and tighten the mounting screws.
6. Route the controller harness to the front of the power
base and reconnect the controller. See figure 10.
7. Secure the controller harness to the armrest receiver
with wire ties if desired.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pride Athena at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pride Athena in the language / languages: English as an attachment in your email.

The manual is 3,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info