Manual President Harrison (page 30 of 47) (English, German, French, Spanish)

636596

Zoom out

Zoom in

1/47

b) MEMORY 2 : This button is used to store the channel you want at memory

mode.

10)SCAN, DUAL WATCH, MEMORY 3

a) SCAN : The channel Scan feature allows the radio to scan automatically

through all 40 channels, stopping at any channel that is busy with signals

being communicated. It will remain on that channel during the conversation,

and will not reactivate scanning until 5 seconds after the conversation has

ceased.

To Active, press “M1” button, “SCAN, AUTO-Q, MOM, BEEP, EMG” will appear

at the bottom line on the LCD. And then press the “M3” button. The word

“SCAN” will appear at the top line on the LCD. The radio will start the up

scanning process. If you want to stop scanning, simply press the “M3” button.

In ‘the event that during the scanning process the radio stops on a channel

and the conversation that you want to communicate with, simply press the

Push-To-Talk switch in the mike. This will shut off the scanning function and

transmit on that channel. To access the down scanning, turn the channel

switch counterclockwise or press the “t” button on the mike.

b) MEMORY SCAN : The memory channel Scan feature allows the radio to scan

automatically through 7 memorised channels. To access, press “R/M” button

until “M” will appear on the LCD. And then repeat scan process.

c) DUAL WATCH : The Dual Watch feature gives the user the ability to monitor and

communicate over two virtual channels simultaneously. An application of this

may be when you want to be able to communicate on a “quiet” channel (for

example, channel 28), while at the same time monitoring conversation

talking place on a very “active” channel (for example, channel 9). To

Operate Dual Watch : 1) Press “M1” button until “BATT, DW, LOCK” will appear

at the bottom line on the LCD. 2) Select the channel in which you want to

monitor, which we will refer to as your “Watch Channel”. 3) Press “M3” button.

The “DW” will appear at the top line on the LCD. 4) Select the other channel

in which you want to monitor using the up/down channel arrows. Once this

channel has been selected, the radio will begin its dual watch monitoring in

about three seconds.

Note that the second channel selected in the primary channel, with the radio

switching to the “Watch Channel” for approximately one second every three

seconds. If a signal is received on the “Watch Channel”, the radio will change

to that channel immediately. If you press the Push-To-Talk switch on the mike

when signal is received at the “Watch Channel”, the “Dual Watch” feature

will turn off. But if you press the Push-To-Talk switch at the second channel, the

“Dual Watch” feature will not turn off. To turn off the ‘Dual Watch” feature,

simply press the “M3” button The “DW” will disappear on the LCD. Note that

the radio will return to the “Watch Channel” for normal operation.

d) MEMORY 3 : This button is used to store the channel you want at memory

mode.

11)AUTO-Q, MEMORY 4

a) AUTO-Q : This control is also used to cut off or eliminate receiver background

noise in the absence of incoming signal. If the incoming signal is lower than

the squelch level, the audio output will decrease. But, audio output will be

same as incoming signal in case that incoming signal is higher than the

squelch level.

To access, press “M1” button, “SCAN, AUTO-Q, MON, BEEP, EMG” will appear

at the bottom line on the LCD. Then press “M4” button, “AUTO-Q” will appear

at top line on the LCD and the incoming signals will be stronger than the

background noise. To stop, press “M4” button once again.

b) MEMORY 4 : This button is used to store the channel you want at memory

mode.

12)MONITOR, LOOK, MEMORY 5

a) MONITOR : This feature is used to listen to a weak signal that repeatedly opens

and closes the squelch without changing the squelch setting. When receiving

a weak signal, push and hold this button to open the squelch completely. To

access, press “M1” button, then “SCAN, AUTO-Q, MON, BEEP, EMG” will

appear at the bottom line on the LCD Then press “M5” button, “BUSY” will

appear on the LCD.

b) LOCK : The Lock feature allows the user to “lock” virtually all buttons on the

radio, so they can not be activated. This will prevent the radio from having its

operation mode changed from the one desired by the user. To Activate; press

“M1” button until “BATT, DW, LOCK” will appear at the bottom line on the LCD

Press ‘the’ “M5” button. The

appears on the display to indicate that this

feature is currently activated.

To De-Activate : Repeat the process described in “To Activate”. The

will

disappear from the LCD.

NOTE : “Power”, “PTT”, “Volume”, “Squelch”, “MON”, and “Lamp” are not

affected.

c) MEMORY 5 : This button is used to store the channel you want at memory

mode.

13)BEEP, MEMORY 6

a) BEEP : Gives the user an audible confirmation through a short beep tone that

the C.B mobile has been turned on. The HARRISON comes with this feature

already turned on. If you would like to deactivate this feature, simply press

“M1” button “SCAN, AUTO-Q, MON, BEEP, EMG” will appear at the bottom line

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of President Harrison in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

President Harrison Manual

Product: