636593
7
Zoom out
Zoom in
Previous page
1/20
Next page
7
4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING
YOUR SET FOR THE FIRST TIME (without trans-mitting and
without using the «push-to-talk» switch on the
microphone):
a) Connect the microphone
b) Check the antenna connections
c) To turn the equipment on :
Press any key so that
flashes. You have about 10 seconds in which to
enter your access code.
Press «PROGRAM» key four times (access code pre-determined in the factory).
Each time you press a key, the counter in the display increases by one. Press
the «POWER» key once. Your CB radio will light up and automatically go to
Channel 19, in AM. (MIC GAIN and RF GAIN set to maximum).
If you make a mistake while entering your access code, press any key (several
times, if necessary) until
flashes and then press four times PROGRAM and
then POWER.
d) Turn the squelch knob to minimum (anti-clockwise). Turn the «RF POWER»
switch to maximum (clockwise). Adjust the volume to a comfortable level.
e) Go to Channel 20 using either the «CH » key on the microphone or on the
front panel, or the rotary knob.
5) ADJUSTMENT OF SWR (Standing wave ratio):
WARNING : This must be carried out when you use your CB radio for the first time
(and whenever you re-position your antenna). The adjustment must be
carried out in an obstacle-free area.
* Using the integrated SWR meter:
For this, carry out the following steps :
a) Press the «push-to-talk» switch on the microphone and keep it pressed down
throughout the adjustment.
b) Press the «METER» key until appears in the display.
c) Adjust the SWR/CAL key so that
the 7 rows (like a bar graph ) appear in the display, with the RF/POWER knob
turned to maximum.
d) Press again the «METER» key so that «SWR» appears in the display and the
disappears. It is now possible to take the SWR reading. If in the display there
are less than three rows of the bar graph, then the SWR reading is acceptable
(1 being the ideal SWR value). If there are Minimum value more than three
rows, we advise you to re-adjust your antenna and re start the procedure from
step a).
e) Press the «METER» key, with the «push-to-talk» switch pressed down, so that the
equipment is in S/RF mode.
DISPLAY
Maximumvalue
Minimum value
7


Need help? Post your question in this forum.

Forumrules
1

Forum

president-george

Reset search

  • which button on a president george is the function button Submitted on 2-10-2021 at 12:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for President George at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of President George in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of President George

President George User Manual - Dutch, French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info