636592

President Billy Manual

22
Zoom out
Zoom in
Previous page
1/36
Next page
22
3) POWER CONNECTION:
Your PRESIDENT BILLY is protected against an inversion of polarity. However,
before switching it on, you are advised to check all connections. Your
equipment must be supplied with a direct current of 12 volts (11). Today, most
cars and lorries are negative earth. You can check this by making sure that
the negative terminal of the battery is connected either to the engine block
or to the chassis. If this is not the case, you should consult your dealer.
WARNING: Lorries generally have two batteries and an electrical installation
of 24 volts, in which case it will be necessary to insert a 24/12 volt converter
(type CV 24/12 PRESIDENT) into the electrical circuit. The following connection
steps should be carried out with the power cable disconnected from the set.
a) Check that the battery is a 12 volts one
b) Locate the positive and negative battery terminals (+ is red and - is black).
Should it be necessary to lengthen the power cable, you should use the same
or a superior type of cable.
c) It is necessary to connect your CB to a permanent (+) and (-). We advise you
to connect the power cable directly to the battery (as the connection of the
CB cable to the wiring of the car-radio or other parts of the electrical circuit
may, in some cases, increase the likelihood of interference).
d) Connect the red wire (+) to the positive terminal of the battery and the black
(-) wire to the negative terminal of the battery.
e) Connect the power cable to your CB radio.
WARNING: Never replace the original fuse (2 A) by a different value one.
4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING
YOUR SET FOR THE FIRST TIME (without transmitting and
without using the «push-to-talk» switch on the microphone):
a) Connect the microphone
b) Check the antenna connections
c) Turn the set on by commuting the ON/OF switch on position ON.
d) Turn the SQUELCH knob to minimum (counterclockwise).
e) Adjust the volume knob to a comfortable level.
f) Go to Channel 20 using the CHANNEL knob (6).
5) ADJUSTMENT OF SWR (Standing wave ratio):
WARNING: This must be carried out when you use your CB radio for the first time
(and whenever you re-position your antenna). The adjustment must be
carried out in an obstacle-free area.
* Using an external SWR meter (e.g. SWR 1 or SWR 2):
a) To connect the SWR meter :
- Connect the SWR meter between the CB radio and the antenna as close as
possible to the CB (use a maximum of 40 cm cable, type President CA 2C).
b) To adjust the SWR meter:
- Set the CB to channel 20.
- Put the switch on the SWR meter to position CAL(calibration).
- Press the «push-to-talk» switch on the microphone to transmit.
- Bring the index needle to ▼ by using the calibration key.
- Change the switch to position SWR (reading of the SWR level). The reading on
the S- meter should be as near as possible to 1. If this is not the case, re-adjust
your antenna to obtain a reading as close as possible to 1. (A SWR reading
between 1 and 1.8 is acceptable).
- It will be necessary to re-calibrate the SWR meter after each adjustment of the
antenna.
Your CB is now ready for use.
B) HOW TO USE YOUR CB :
1) POWER:
This switch allows to turn the set on or off.
Zum
chassis
Connected
to chassis
Zum
starter
Towards
starter
English
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for President Billy at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of President Billy in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info