604328
100
Zoom out
Zoom in
Previous page
1/111
Next page
Completing Assembly
15
Checking the Alignment
Proper belt alignment allows the belt to remain centered and ensures smooth
operation. Realigning the belt takes a few simple adjustments. If you are unsure
about this procedure, call Precor Customer Support. Refer to Obtaining Service.
CAUTION: Special care must be taken when aligning the running belt. Turn Off the
treadmill while adjusting or working near the rear roller. Remove any loose clothing and
tie back your hair. Be very careful to keep your fingers and any other object clear of the
belt and rollers, especially in front of the roller and behind the deck. The treadmill will
not stop immediately if an object becomes caught in the belt or rollers.
To check the alignment:
1. The treadmill has adjustable rear feet. Make sure that the running surface is
level before aligning or adjusting the running belt. For more information, see
Leveling the Treadmill.
2. Connect the power plug to an appropriate dedicated circuit and turn the unit
On.
3. Stand beside the treadmill and press QUICKSTART.
Note: If needed, enter the password. Refer to your owner’s manual. The
running belt starts automatically after a 3-second countdown appears on the
display.
4. Increase the treadmill belt speed until the display shows a speed of 3 mph (5
kph).
CAUTION: If you hear any chafing or see that the running belt appears to be getting
damaged, stop the running belt immediately by pressing the red STOP button.
Contact Precor Customer Support.
5. Walk around to the rear of the unit and observe the belt for a few minutes.
The belt should run centered along the running bed. If the belt drifts off center,
you will need to make adjustments. Refer to the next section.
Important: If the belt needs alignment, make the adjustments at once. Failure to
align the belt may cause the belt to tear or fray, which is not covered by the Precor
Limited Warranty.
6. To stop the running belt, press the red STOP button.
7. Turn the treadmill Off.
Adjusting the Running Belt
If you are unsure about adjusting the running belt, contact Precor Customer
Support. Refer to Obtaining Service.
CAUTION: For your safety, use the power switch to turn Off the treadmill before
making any adjustments. Do not adjust the running belt when someone is standing on
the unit.
To adjust the running belt:
1. Locate the right belt adjustment bolt in the rear end cap of the treadmill.
Figure 24: Belt adjustment bolt location
2. To determine left and right, stand at the rear of the treadmill and face the
display. Make all belt adjustments on the right rear corner bolt using the
6 mm hex key.
If the belt is off center to the LEFT, turn the adjusting bolt ¹₄ turn
counterclockwise, which moves the running belt to the right.
If the belt is off center to the RIGHT, turn the bolt ¹₄ turn clockwise,
which moves the belt to the left.
Important: Do not turn the adjusting bolt more than
¹₄
turn at a time.
Overtightening the bolt can damage the treadmill.
3. Recheck the alignment of the running belt.
100


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Precor TRM 243 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Precor TRM 243 in the language / languages: English as an attachment in your email.

The manual is 12,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info