604336
20
Zoom out
Zoom in
Previous page
1/24
Next page
Assembly and Maintenance Guide
S3.23
Strength-Training
Fitness Equipment
S3.23 Assembly and Maintenance Guide
page 2
IMPORTANT SAFETY INSTRUCTIONS
Important Safety Instructions
Important Safety Instructions
Before beginning any fitness program, consult your
physician and receive a thorough physical examination.
Il est conseillé de subir un examen médical complet
avant d’entreprendre tout programme d’exercise. Si
vous avez des étourdissements ou des faiblesses,
arrêtez les exercices immédiatement.
When using exercise equipment, basic precautions
should always be taken, including the following:
Read all instructions before using the S3.23
equipment. These instructions are written for your
safety and to protect the unit.
Do not allow children or those unfamiliar with its
operation on or near the equipment. Do not leave
children unsupervised around the unit
Use the equipment only for its intended purpose as
described in this manual. Do not use accessory
attachments that are not recommended by the
manufacturer, as such attachments may cause
injuries.
Wear proper exercise clothing and shoes for your
workout and avoid loose clothing. Tie long hair
back.
Use care when getting on or off the unit.
Do not overexert yourself or work to exhaustion.
If you feel any pain or abnormal symptoms,
stop your workout immediately and consult
your physician.
Never operate the unit when it has been dropped
or damaged. Return the equipment to a service
center for examination and repair.
Never drop or insert objects into any opening.
Keep hands away from moving parts.
Always check the unit and its cables before each
use. Make sure that all fasteners and cables are
secure and in good working condition.
Do not use outdoors.
Personal Safety during Assembly
It is strongly recommended that a qualified
dealer assemble the equipment. Assistance is
required.
Read each step in the assembly instructions and
follow the steps in sequence. Do not skip ahead. If
you skip ahead, you may learn later that you have
to disassemble components and that you may
have damaged the equipment.
Assemble and operate the S3.23 on a solid, level
surface. Locate the unit a few feet from walls or
furniture to provide easy access.
Obtaining Service
Do not attempt to service the S3.23 yourself
except for the maintenance tasks described
in this guide. This unit does not contain any
user-serviceable parts.
For information about product operation,
refer to the enclosed DVD. For service,
refer to the Precor web site at
www.precor.com. Should you need more
information regarding customer support
numbers or a list of Precor authorized
service centers, visit the Precor website at
www.precor.com/contact.
If you call or e-mail Customer Service, have
the serial number and part numbers
available.
You can find the serial number printed on
a label affixed to the side of the S3.23. For
future reference, write the serial number in
the space provided below.
Serial number: ______________________
S3.23 Assembly and Maintenance Guide
page 3
Table of Contents
1
2
3
Important Safety Instructions ...................................................................................................2
Personal Safety During Assembly ............................................................................................ 2
Obtaining Service .................................................................................................................... 2
Before You Begin ........................................................................................... 4
Unpacking the Equipment ....................................................................................................... 4
Preparations ................................................................................................... 5
Required Tools ......................................................................................................................... 5
Installation Requirements ........................................................................................................ 5
Assembly Tips ......................................................................................................................... 5
Assembly Instructions .................................................................................. 6
Open Box 1 ............................................................................................................................. 7
1. Assemble Main Structure .............................................................................................. 8
2. Assemble Weight Stack ................................................................................................ 9
Open Box 2 ............................................................................................................................. 13
3. Attach Shrouds ............................................................................................................. 14
4. Attach Handles and Accessories .................................................................................. 15
5. Move the Pulley Assemblies ......................................................................................... 16
Adjustments and Maintenance ..................................................................... 17
1. Cable Adjustments ........................................................................................................ 18
2. Selector Stem Adjustments ........................................................................................... 18
3. Maintenance ................................................................................................................. 19
Limited Warranty Statement .................................................................................................... 20
Warranty Registration Card ..................................................................................................... 21
Specifications ............................................................................................................. Back cover
4
Table of Contents
S3.23 Assembly and Maintenance Guide
page 4
1
Before You Begin
Before You Begin
Thank you for purchasing the S3.23. This unit is part of
the Precor Strength line of quality strength training
machines, which let you target specific muscle groups
to achieve better muscle tone and overall body
conditioning. To maximize your use of the equipment,
please study this guide thoroughly.
Unpacking the Equipment
The S3.23 is carefully tested and inspected before
shipment. Precor Strength ships the unit in several
pieces that require assembly. Ask for assistance during
the assembly process.
Review the Installation Requirements found on the
next page.
When instructed to open a box, carefully unpack
the pieces and lay them on the floor near the
location where you plan to use the equipment.
Be careful to open boxes and assemble components
in the sequence presented in this manual.
If any items are missing, contact the dealer from whom
you purchased the unit. For more information, refer to
Obtaining Service.
S3.23 Assembly and Maintenance Guide
page 5
2
Preparations
Preparations
CAUTION: To set up this unit, you will need
assistance. Do not attempt assembly by yourself.
You must review and follow the instructions in this
guide. If you do not assemble and use the S3.23
according to the following guidelines, you could void
the Precor Limited Warranty.
Required Tools
Tools that you need to obtain before assembling the
unit include:
Standard set of hex keys
Two ⁹⁄₁₆-inch wrenches
One ¹⁄₂-inch wrench
Wire tie cutter (cuts plastic tie wraps)
Step stool
Note: Use box-end, open-end or standard crescent
wrenches.
Installation Requirements
Follow these installation requirements when
assembling the unit:
Fill out and mail the warranty registration card.
Set up the S3.23 on a solid, flat surface.
A smooth, flat surface under the unit helps keep
it level.
Provide ample space around the machine.
Open space around the machine allows for easier
access.
Insert all fasteners in the same direction. For
aesthetic purposes, insert all the fasteners in the
same direction unless specified (in text or
illustrations) to do otherwise.
Leave room for adjustments. Tighten fasteners
(such as screws, nuts, and bolts), so the unit is
stable, but leaves room for adjustments. Do not
fully tighten fasteners until instructed (in the steps)
to do so.
Assembly Tips
A black 6-inch scale with white numbers is
provided at the bottom of every assembly
instruction page. Use this scale to identify the
correct fastener size. The head of a fastener is not
used in measuring the length.
To find out the length of a particular fastener,
measure its shank (the long, narrow part beneath
the head). Refer to the following diagram:
Silver fasteners are used within the silver painted
areas. Black fasteners are used when assembling
the gray painted surfaces.
Some pieces have extra holes that you will not use.
Use only those holes indicated in the instructions
and illustrations.
Read all caution notes on each page before
completing that step.
While you may be able to assemble the S3.23 by
reading the illustrations only, refer to the text for
important safety cautions and notes.
Fastener head
Fastener threads
Shank
To determine the
length of a fastener,
measure its shank.
S3.23 Assembly and Maintenance Guide
page 6
1 2 3 4 5 6
3
Assembly
Instructions
Assembly Instructions
Assembly of the S3.23 takes professional installers
about 1 hour to complete. If this is the first time you
have assembled this type of equipment, plan on
significantly more time.
Professional installers are highly recommended!
However, if you acquire the appropriate tools, obtain
assistance, and follow the assembly steps sequentially,
the process will take time, but is fairly easy.
CAUTION: Obtain assistance! Do not attempt to
assemble the S3.23 by yourself. Review the
Installation Requirements on page 6 before
proceeding with the following steps.
The S3.23 comes in two long boxes with four smaller
boxes of weights.
Be careful to open boxes and assemble components
in the sequence presented in this manual.
Note: With so many assembled parts, proper alignment
and adjustment is critical. While tightening the fasteners,
be sure to leave room for adjustments. Do not fully
tighten fasteners until instructed to do so.
S3.23 Assembly and Maintenance Guide
page 7
1 2 3 4 5 6
Open Box 1
Open Box 1
Use wire tie cutters to open the boxes.
In this section, you will assemble the Main Structure
of the S3.23. The illustration shows how the Main
Structure will look when you have completed its
assembly.
Mid Cross
Brace
Chin-up Bar
Main Upright
Main Upright
S3.23 Assembly and Maintenance Guide
page 8
1 2 3 4 5 6
Main Uprights
4 - 2¹⁄₂" bolts
8 - washers
4 - locknuts
B
Step 1. Assemble Main Structure
1. Assemble Main Structure
A. Lift and stabilize the two Main Uprights.
B. Have an assistant hold the Main Uprights steady
while you attach the Mid Cross Brace using
four 2¹⁄₂-inch hex head bolts
eight washers
four locknuts
Note: Alternately finger tighten all four fasteners
while adjusting the alignment of the Main Uprights.
C. Attach the Chin-up Bar to the Main Uprights
using
four ³⁄₄-inch hex head bolts
four washers
CAUTION: Make sure that the assembled parts
are stable and balanced before your assistant
lets go of the Main Uprights.
D. Use two ⁹⁄₁₆-inch wrenches to tighten the fasteners
beginning with the Mid Cross Brace.
E. Wrench tighten the Chin-up Bar fasteners.
F. Set aside the accessories and handles found in
Box 1.
Mid Cross Brace
Attach Mid
Cross Brace
4 - ³⁄₄" bolts
4 - washers
C
Mid Cross
Brace
Rear view
D
E
Tighten four Mid
Cross Brace
fasteners.
Tighten four
Chin-up Bar
fasteners.
S3.23 Assembly and Maintenance Guide
page 9
1 2 3 4 5 6
Step 2. Assemble Weight Stack
2. Assemble Weight Stack
Note: Perform the following steps on each Main
Upright. Complete the assembly steps for one side
before moving the other Main Upright.
A. Have your assistant lift the Top Cap Weight to
remove cable tension.
B. Use a hex key to remove the two buttonhead
screws and two washers that secure the Guide
Rod Bracket.
C. Remove the Guide Rod Bracket and Bumpers.
Top Cap Weight
B
C
A
Guide Rod
Bracket
Bumpers
Guide Rods
Cable
Main Upright
Selector Stem
S3.23 Assembly and Maintenance Guide
page 10
1 2 3 4 5 6
D. Have your assistant slide the Top Weight Assembly
and Selector Stem off the Guide Rods. Ask your
assistant to hold the Top Weight Assembly away
from the Guide Rods while you install the weights.
E. Add the ten 10-lb weights and the ten shorter-
length 5-lb weights. Note that the curve on the
weight plate faces inside. Hold your finger over the
plastic bushing in each weight to prevent the
bushing from popping out.
CAUTION: The weights are heavy! Handle the
weights carefully so as not to drop them or
injure yourself. Pick up and place one weight at
a time on the Guide Rods. Do not angle the
Guide Rods to such a degree that they dislodge
the Base Bumpers and come out of the Base
Frame.
Step 2. Assemble Weight Stack, Continued
Top Weight
Assembly
Guide Rod
Bracket and
Bumpers
E
D
Guide Rod
Guide Rods
Ask your assistant to hold the Top Cap Weight
Assembly away from the Guide Rods while you
install the weights.
Base Bumpers
Base
Frame
Selector Stem
S3.23 Assembly and Maintenance Guide
page 11
1 2 3 4 5 6
Step 2. Assemble Weight Stack, Continued
H
G
F. Hold the Guide Rods while your assistance
replaces the Selector Stem and Top Weight
Assembly.
Important: During reassembly, do not lower the
Guide Rod Bracket more than three inches along
the Guide Rods. Have your assistant hold the
Guide Rods firmly because they can be pulled out
of the Base Bumpers. It is difficult to replace the
Guide Rods in an assembled Weight Stack. If the
Guide Rods become dislodged, you will need to
disassemble the Weight Stack to make sure that
the Guide Rods are seated properly in the Base
Frame.
G. Ask your assistant to hold the Guide Rods while
you check the cables to make sure they are
centered between the Guide Rods. Remove any
twists in the cables.
H. To relieve cable tension, lift the Top Cap Weight
about a foot above the Weight Stack and secure it
with the Weight Pin.
I. While your assistant continues to hold the Guide
Rods, realign the Rubber Bumpers with the cutouts
in the Upper Frame Crosspiece. Replace the Guide
Rod Bracket using two buttonhead screws and two
washers (removed in step 2B).
Wrench tighten.
F
Guide Rod
Weight
Stack
I
Weight
Pin
Guide Rod
Bracket
Align the Rubber Bumpers with
cutouts in the Upper Frame Cross-
piece.
Rubber
Bumpers
Upper
Frame
Crosspiece
Selector
Stem
Top Cap
Weight
Top Weight
Assembly
S3.23 Assembly and Maintenance Guide
page 12
1 2 3 4 5 6
J. Remove the Weight Pin and gently lower the Top
Cap Weight onto the Weight Stack.
K. Remove the slack in the cable. Use two ⁹⁄₁₆-inch
wrenches to loosen the fastener that holds the
Cam Washer. Rotate the Cam Washer to remove
any slack in the cable. Check the Top Cap Weight
to make sure it remains well-seated on the Weight
Stack and then wrench tighten the Cam Washer
fasteners.
L. Peel the Weight Label off the Weight Label Strip.
M. Peel the backing off the Weight Label to expose
the adhesive and place a label on each Weight
Plate. The recommended location of the label is
toward the rear of the unit.
N. Apply one tube of lubricant to each Guide Rod.
CAUTION: The lubricant can stain clothes. Wear
proper attire when lubricating the Guide Rods.
J
Weight
Pin
Top Cap
Weight
K
Cam
Washer
Top Cap
Weight
Adjust Cam Washer to
remove cable slack.
Remove Weight Pin and
lower Top Cap Weight.
N
5 lb
Weight
Stack
10 lb
Weight
Stack
Lubricant Guide Rod
Step 2. Assemble Weight Stack, Continued
25
27.5
30
35
40
45
50
55
60
65
70
75
80
L
10
17.
5
20
22.5
25
7.5
15
12.
5
M
Weight Label Strip
Weight
Label
S3.23 Assembly and Maintenance Guide
page 13
1 2 3 4 5 6
Open Box 2
Open Box 2
Use tie cutters to open the box.
The illustration shows the entire S3.23 assembly once
you have completed installing the contents of Box 2.
S3.23 Assembly and Maintenance Guide
page 14
1 2 3 4 5 6
Step 3. Attach Shrouds
3. Attach Shrouds
Two Shrouds are attached to each Main Upright.
Complete the assembly steps for one side before
moving the other Main Upright.
Important: Handle the Shroud with care. The acrylic
Shrouds require special handling as they are easily
scratched. For proper care and maintenance, refer to
the Adjustments and Maintenance section in this
guide.
A. Install the Shrouds so the cutouts allow access to
the Weight Stack Pin.
B. Attach a Shroud to each side of the Main Upright
using
six 1³⁄₄-inch Socket head screws
six spacers
Note: Start at the top two mounts and work toward
the base. Ask your assistant to hold the Shroud in
place while you insert the top spacers and
fasteners. Alternately finger tighten all six fasteners
while adjusting the alignment.
C. Wrench tighten all the fasteners using a hex key.
CAUTION: Do not over tighten. You can crack or
warp the Shroud if too much pressure is applied to
the fasteners.
Shroud
Cutout in
Shroud
C
6 - 1³⁄₄" Socket head screws per Shroud
6- spacers per Shroud
B
S3.23 Assembly and Maintenance Guide
page 15
1 2 3 4 5 6
Step 4. Attach Handles and Accessories
4. Attach Handles and
Accessories
A. Install a Handle on each Pulley Assembly
using
one 5mm Socket head screw
Wrench tighten with a hex key.
Note: To adjust the outside pulley location, lift the
Handle and slide it to the desired location.
B. Attach the two Soft Handles or a Soft Ankle Strap
to the end of the cable using a Spring Clip.
This completes the assembly of your S3.23 Strength-
Training Fitness Equipment.
A
B
Install the Soft Handle or
Soft Ankle Strap.
Pulley Assembly
1 - 5mm Socket head screw on
each Pulley Assembly
Spring
Clip
Soft
Handle
S3.23 Assembly and Maintenance Guide
page 16
1 2 3 4 5 6
5. Move the Pulley Assemblies
A. To raise the Pulley Assembly, simply push the
Handle up along the track. The Pulley Assembly
automatically locks into position.
To lower the Pulley Assembly, lift the Handle up so
it disengages from the track and then lower the
Pulley Assembly. Let go of the Handle to lock the
Pulley Assembly into position.
Step 5. Move the Pulley Assemblies
A
Pulley
Assembly
Handle
To disengage the Pulley Assembly, lift the
Handle and slide the assembly along its track.
S3.23 Assembly and Maintenance Guide
page 17
1 2 3 4 5 6
4
Adjustments and
Maintenance
Adjustments and Maintenance
When the S3.23 is completely assembled, you need to
check the cables for proper tension. Obvious signs that
cable problems exist include:
Top Cap Weight does not rest squarely on the top
weight of the Weight Stack.
Cable rubs the inside edges of the pulleys.
Excess slack exists in the cable.
Weight Pin cannot be easily inserted in or
removed from each hole in the Weight Stack.
Selector Stem rubs inside the Weight Stack.
CAUTION: Take the time to perform the following
steps. If the cables do not have the proper tension
you could void the Precor Limited Warranty.
Important: To access cables and the Selector Stem,
you will need to remove the Shrouds.
Top Cap Weight
Weight pin
A slack cable
Pulley
Weight Stack
Holes in Weight Stack
S3.23 Assembly and Maintenance Guide
page 18
Adjustments and Maintenance, Continued
1. Cable Adjustments
The Cam Washer ensures easy cable adjustments.
A. To remove the slack in the cable. Use two ⁹⁄₁₆-inch
wrenches to loosen the fastener that holds the
Cam Washer.
B. Rotate the Cam Washer so that the slack is
removed.
C. Check the Top Cap Weight to make sure it remains
well-seated on the Weight Stack and then wrench
tighten the Cam Washer fasteners.
D. Check the Selector Stem alignment by inserting
the Weight Pin into every hole on the Weight Stack.
Cam Washer
Top Weight
Assembly
A
B
C
A
2. Selector Stem Adjustments
If the Selector Stem consistently strikes the inside of
the weight stack or it is misaligned with the Weight
Stack hole, you can re-center the Selector Stem by
taking the following steps:
A. To free the Selector Stem, remove the Weight Pin
from the Weight Stack.
B. Pull up the Selector Stem and place a cover over
the opening in the Weight Stack. Rest the Selector
Stem on the cover.
C. Use an 8mm hex key to loosen the socket head
bolt in the center of the Top Cap Weight.
Important: Do not remove the socket head bolt.
D. Remove the cover from the Weight Stack and
lower the Selector Stem so the Top Cap Weight
rests on the Weight Stack.
E. To lock the Selector Stem, insert the Weight Pin
into the Weight Plate hole at the bottom of the
Weight Stack.
F. Wrench-tighten the socket head bolt in the center
of the Top Cap Weight.
G. Check the adjustment by inserting the Weight Pin
into every Weight Plate hole. The Weight Pin
should slide easily in and out of each Weight Plate
and Selector Stem.
H. Insert the Weight Pin into the appropriate Weight
Plate for your level of fitness.
J. Replace the Shroud, if necessary.
C
B
S3.23 Assembly and Maintenance Guide
page 19
3. Maintenance
Guide Rods
A Apply one tube of lubricant to each Guide Rod.
B. Lubricate the Guide Rods every six months. Obtain
the proper lubricant from your dealer.
CAUTION: The lubricant can stain clothes. Wear
proper attire when lubricating the Guide Rods.
Lubricant
Guide Rod
Adjustments and Maintenance, Continued
Inspection
Inspect the unit daily.
Look and listen for frayed or worn parts, loose
fasteners, cable tension issues, unusual noises, and
any other indications that the equipment may be in
need of service.
You are responsible for the proper maintenance of the
unit as discussed in this manual. For other service
issues, contact Customer Support. Refer to Obtaining
Service.
Shrouds
CAUTION: Clean the Shrouds with product
specifically labeled as safe for acrylic. Use a clean,
nonabrasive cloth and light pressure to avoid
scratching the acrylic surface.
The acrylic Shrouds on the S3.23 are easily scratched
or damaged through improper cleaning techniques. To
avoid problems, dust the shrouds often with a clean,
lint-free cloth and light pressure. Avoid rubbing dirt or
grit into the surface. If you use glass cleaner or a
similar product, make sure the label states that it is
safe to use on Plexiglas
®
or acrylic products.
Important: DO NOT use ketones, aromatics, esters,
halogens, window cleaning sprays, alcohol, kitchen
scouring compounds, or solvents (such as acetone,
benzene, gasoline, carbon tetrachloride, or thinners).
Do not use ammonia-based cleaning solutions
because the ammonia destroys the plastic coating.
To remove light scratches, use a buffing compound
such as, car wax. Lightly buff the acrylic sheet using a
clean buffer until the scratches disappear.
A
Effective 01 January 2003
P/N 36287-110
Precor Residential Equipment Limited Warranty
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING
YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE
CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.
Limited Warranty.
Precor Incorporated warrants all new Precor products to be free from defects in materials and
manufacture for the warranty period set forth below. The warranty period commences on the
invoice date of original purchase. This warranty applies only against defects discovered within
the warranty period and extends only to the original purchaser of the product. Parts repaired or
replaced under the terms of this warranty will be warranted for the remainder of the original
warranty period only. To make claim under warranty, the buyer must notify Precor or their
authorized Precor dealer within 30 days after the date of discovery of any nonconformity and
make the affected product available for inspection by Precor or its service representative.
Precor’s obligations under this warranty are limited and set forth below.
Warranty Periods and Coverage
All residential products and commercial products used in the home are warranted for the
following periods:
Lifetime frame and welds
10 years parts and wear items
1 year labor
Coverage for options and accessories defined below.
Options / Accessories
Many options or accessories have components that are connected internally or mounted inside the
electronic console. The following guidelines determine the warranty for these components. If the
internal components are installed by the factory or by an authorized dealer as part of the original
sale and delivery, they have a warranty that is identical to the warranty of the equipment in which
they are connected or mounted. If the internal components are not installed by the factory or by an
authorized dealer as part of the original sale and delivery, they have a 90-day parts and labor
limited warranty. All components that are not internally connected have 90-day parts only limited
warranty. Satisfactory proof of purchase is required in all cases.
Conditions and Restrictions
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the Precor product only while:
a. It remains in the possession of the original purchaser and proof of purchase is
demonstrated
b. It has not been subjected to accident, misuse, abuse, improper service, or non-Precor
modifications
c. Claims are made within the warranty period
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in
compliance with electrical codes or Precor owner’s manual specifications, or failure to provide
reasonable and necessary maintenance as outlined in the owner’s manual.
3. Warranty of all Precor products applies to residential use only and is void when products are
used in a nonresidential environment or installed in a country other than where sold.
4. Except in Canada, Precor does not pay labor outside the United States.
5. Warranties outside the United States and Canada may vary. Please contact your local Dealer
for details.
This limited warranty shall not apply to:
1. Software version upgrades
2. Cosmetic items, including, but not limited to the following: grips, seats, and labels.
3. Repairs performed on Precor equipment missing a serial number or with a serial tag that has
been altered or defaced.
4. Service calls to correct installation of the equipment or instruct owners on how to use the
equipment.
5. Pickup, delivery, or freight charges involved with repairs.
6. Any labor costs incurred beyond the applicable labor warranty period.
Disclaimer and Release
The warranties provided herein are the exclusive warranties given by Precor and supersede any prior, contrary
or additional representations, whether oral or written. ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVE ARE LIMITED IN
DURATION TO THE PERIODS OF EXPRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS. PRECOR HEREBY DISCLAIMS
AND EXCLUDES THOSE WARRANTIES THEREAFTER.
Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you. PRECOR ALSO HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER OBLIGATIONS OR LIABILITIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH RESPECT TO ANY
NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED TO: (A) ANY OBLIGATION, LIABILITY, RIGHT,
CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS SUPPLIERS (WHETHER
ACTIVE, PASSIVE OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY FOR LOSS OF OR DAMAGE TO
ANY EQUIPMENT.
This disclaimer and release shall apply even if the express warranty set forth above fails of its
essential purpose.
Exclusive Remedies
For any product described above that fails to conform to its warranty, Precor will provide, at their option, one of
the following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty service
may be obtained by contacting the authorized dealer from whom you purchased the item. Precor
compensates Servicers for warranty trips within their normal service area to repair equipment at the owner’s
location. You may be charged a trip charge outside the service area. THESE SHALL BE THE SOLE AND EXCLUSIVE
REMEDIES OF THE BUYER FOR ANY BREACH OF WARRANTY.
Exclusion of Consequential and Incidental Damages
PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT
(INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR
OTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE, REVENUE OR PROFIT, COST OF
CAPITAL, COST OF SUBSTITUTE EQUIPMENT, ADDITIONAL COST INCURRED BY BUYER (BY WAY OF CORRECTION OR
OTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT.
This exclusion
applies even if the above warranty fails of its essential purpose and regardless of whether such damages
are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other
legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation might not apply.
This warranty gives you specific legal rights, and you may also have other rights, which vary state
to state.
Complete this portion and keep for your records.
Purchased From: ____________________________ Example: Dealer or store name.
Phone Number: _____________________________ Example: Dealer or store telephone number.
Product/model: _____________________________ Example: M9.31
Serial number: ______________________________ The serial number is found on the shipping container
page 20
Fold along dotted line and tape closed before mailing.
page 21
RET.
To allow us to serve you better, please take a few moments to
complete and return your warranty registration.
YOU MAY ALSO REGISTER ONLINE AT
www.precor.com/warranty
If you have questions or need additional information, contact your
local dealer or call Precor Customer Support at 800-347-4404.
Thank You and Welcome to Precor
Precor Incorporated
20031 142nd Avenue NE
PO Box 7202
Woodinville, WA 98072-4002
PLACE
STAMP
HERE
page 22
TELL US ABOUT YOUR NEW PRECOR PRODUCT
Purchased
from:
The serial number is located on the shipping box and on the product.
Product
Serial
Number:
Please indicate the type of product purchased:
Elliptical Fitness CrossTrainer (EFX
®
)
Treadmill
Strength Training System
TELL US ABOUT YOU
Date of
Purchase:
Mr.
Mrs.
Ms.
First Name
Apt./Suite:
TELL US ABOUT YOUR PURCHASE
Please detach and mail in the warranty registration within ten days of purchase.
StretchTrainer
TM
Cycle
Stair Climber
Middle Initial Last Name
Street Address
Zip CodeCity State
Gender: Marital status: Age: Annual household income: What are your fitness goals?
Male Married Under 18 Under $50,000 Weight loss/management
Female Divorced 18-24 $51,000-75,000 Muscle tone enhancement
Widowed 25-34 $76,000-100,000 Cardiovascular improvement
Never been married 35-44 $101,000-150,000 Overall health
45-54 $151,000+ Increase energy and flexibility
55-64 Stress reduction
65+ Rehabilitation
Other
Purchase (check all that apply): How did you FIRST become aware of Precor
First Precor product products (choose only one):
Replaces a Precor product of the same type A gift
Replaces same type of product – different brand Friend/relative
Addition to equipment currently owned Physician
Fitness club
Internet
What factors MOST influenced your decision to News report or product review
purchase your Precor product (choose up to three): Magazine advertisement or article
Precor reputation Print advertisement
Prior use of Precor product(s) In-store display or demonstration
Design/appearance Other
Value for the price
Special product features
Rebate or sale price
Quality/durability
Warranty
Physician recommendation
Month
Day
Year
Your Email Address
Area Code
Telephone
Dealer Name
Effective 01 July 2004
P/N 45623-102
Precor is a registered trademark of Precor Incorporated.
Specifications subject to change without notice.
Copyright 2008 Precor Incorporated.
www.precor.com
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
NOTICE:
Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. and foreign patents for
both the mechanical construction and the visual aspects of its product design. Any party contemplating the use of Precor’s product designs is hereby
forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor will vigorously pursue all
unauthorized appropriation of its proprietary rights.
S3.23 Specifications
Length: 38 inches (97 cm)
Height: 83 inches (211 cm)
Width: 52.5 inches (133 cm)
Shipping weight: 289 lb (131 kg)
Literature Kit # 48607-106
Owner's Manual # 48608-106
Registration Card # 45623-102
Warranty Statement # 36287-110
21 April 2008
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Precor S3.23 Strength-Training at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Precor S3.23 Strength-Training in the language / languages: English as an attachment in your email.

The manual is 3,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info