685328
37
Zoom out
Zoom in
Previous page
1/56
Next page
GENERATOR ENCLOSURES
Some installations require the Genset to be mounted inside an enclosure. Enclosures are
generally constructed of heavy gauge sheet metal, and completely insulated. Enclosures are
typically installed in RV’s with large unobstructed compartments. The major advantage to
installing a Genset in an enclosure is to achieve a significant reduction in the unit’s sound level.
In order to maintain the ambient temperature within the enclosure a forced cool air
system is generally employed. Two blower fans capable of producing a minimum of 465 CFM
each should be mounted at the generator end of the enclosure. Cooling air circulates around the
generator end and engine, forcing excess heat to exit through an air duct outlet to the outside air.
Since hot air will rise the air duct outlet opening should be located near the inside top surface of
the enclosure, the opening should be approximately 25 square inches.
Openings in the base of the enclosure and compartment floor are required for the engine
exhaust pipe, oil drain hose and engine breather hose. Other holes for fuel lines, electrical leads,
remote radiator hoses, etc. are usually located in the rear wall of the enclosure. Be sure to seal
around these items to prevent fumes or vapors from entering the vehicles compartment. Two
hinged doors at the front of the enclosure enable unobstructed access to the engine and control
box for routine maintenance. A removable service panel in the rear wall of the enclosure
facilitates servicing the back side of the Genset.
The clearance between the enclosure and the vehicles compartment walls is another
consideration. Except for the rear wall of the enclosure the clearances at the top, sides and front
can be minimal. A ½” gap per side is enough clearance for easy installation or removal. At the
rear of the enclosure the compartment depth must be large enough to accommodate the two
blower fans and system connections. A minimum of 10” between the enclosure and rear
compartment wall is required for this area. Also, remember a 400 sq. inch free air opening is
required to supply the forced air cooling system. See section on “Air Requirements” for details.
Dimensions and layouts are provided for your planned installation, be sure to follow all
requirements. Power Technology’s Customer Service Department is available to answer any
questions you may have concerning your Genset and installation.
IMPORTANT: When installing a RV generator set the installation must comply with the
current Safety Standards of ANSI / RVIA EGS-1-2003, ANSI A 119.2 / NFPA 501C and
applicable articles of ANSI / NFPA 70 of the National Electrical Code. Generator set
installations must also comply with state and local requirements.
IMPORTANT: An enclosure manufactured by any person (s) other then Power Technology
must follow the requirements set forth in this manual. All specifications must be adhered to;
failure to do so may affect your Power Technology Southeast, Inc. Limited Warranty.
7
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech PTRV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech PTRV in the language / languages: English as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info