685359
38
Zoom out
Zoom in
Previous page
1/51
Next page
GENERATOR INSTALLATION
in RECREATIONAL VEHICLES
INTRODUCTION
Use this section as a guide when installing a generator set in a recreational vehicle, and then refer
to the appropriate operation section for specific instructions. The installation of a RV generator set shall
comply with current standards of ANSI / RVIA EGS-1, NFPA 1192 / ANSI A 119.2, ANSI / NFPA 70,
NFPA 551 and applicable articles of the National Electrical Code. Generator set installations must also
comply with state and local requirements.
MARINE APPLICATION
RV generator sets do not comply with United States Coast Guard (USCG) requirements and
must not be used for marine applications. Use only generator sets specified for marine use in marine
installations. USCG regulation 33CFR183 requires a generator set to be “ignition protected” when used
in a gasoline fueled environment.
GENERAL INFORMATION
This information section covers the PTRV generator models listed below. To determine which
model is involved, check the model number found on the Power Technology nameplate attached to the
frame of the generator being installed. Follow all instructions to ensure proper installation and operation.
Each generator set features a Kubota diesel engine, rotating-field alternating current generator,
and a relay controller. The generator is directly connected to the engine for permanent alignment. Each
controller includes a Start / Stop switch for test operating the set at the controller. Also included is an On
/Off switch to reset the controller or lockout any remote switch to prevent starting while service is being
performed. The controller may be equipped with a switch to operate the mechanism used to move the
generator out of the coach for servicing. (Supplied by the coach manufacture). After the set is attached
to the frame of the vehicle, all that is usually required to make it operational is the following.
1. Attaching the exhaust system.
2. Add proper amount of radiator coolant.
3. Add oil to crankcase, to the dipstick FULL mark.
4. Connect fuel lines, remote switch, load leads and battery terminals.
(Consult the Specification Charts on the Following Pages for Requirements)
3
MODEL PTRV-8 KSI PTRV-10-12 KSI
GENERATOR DIMENSIONS L x W x H 38.5” x 24.5” x 24” 45” x 24.5” x 24”
WEIGHT 515 lbs. 620 lbs.
ENGINE Kubota D1105 Kubota V1505
RPMs 1800 1800
KW RATING 8 10-12
AC VOLTAGE 120 or 120 / 240 120 or 120/240
AMPERAGE 66 / 33 10KW-83/41
12KW- 100/50
Hz 60 60
PHASE 1 1
GENERATOR COMPARTMENT
FREE AIR OPENING
125
Square Inches
125
Square Inches
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech PTRV- 8 KSI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech PTRV- 8 KSI in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info