685358

PowerTech PTRV- 3 RR Manual

39
Zoom out
Zoom in
Previous page
1/44
Next page
EXHAUST SYSTEM
Exhaust system components supplied with your unit are specifically designed for optimum performance
and safety. It is imperative to install the muffler and tailpipe to reduce exhaust noise and direct exhaust gases
beyond the vehicles perimeter and away from the normal head-on air stream. Install the tail pipe with as few
bends as possible to prevent excessive backpressure. A properly installed exhaust system must be vapor tight,
quiet and completely safe for the vehicle, its occupants and surroundings.
IMPORTANT SAFETY TIPS:
Replacement Exhaust System components which are not furnished by Power Technology SE, Inc., must
meet the following requirements. It is the responsibility of the installer and owner to use the proper
materials and installation techniques to assure a safe and trouble free Exhaust System.
1) Only use exhaust system components, which do not restrict exhaust flow. A restricted exhaust
system will create excessive backpressure and may cause poor engine performance and possible
engine damage.
2) Muffler shall be fabricated of aluminized steel or other corrosion resistant material and be of a
welded or crimp construction. A USDA Forest Service approved spark arrestor must be part of the
integral design of the muffler or provided as a separate add-on item.
3) Maintain a minimum of 3 inches (76mm) between the exhaust system components and any
surrounding combustible materials. If the minimum clearance cannot be maintained, an insulating
shield must be installed to prevent the combustible material from exceeding temperatures of 117°F
(65°C) above ambient temperature.
4) Extend the exhaust system a minimum of 1 inch (25mm) beyond the vehicles perimeter. Never
terminate the exhaust system underneath the vehicle.
5) Terminate the exhaust system in a direction, which prevents the exhaust gases from being drawn
back into the generator compartment and re-circulated.
6) If the exhaust system in located in an area which may become susceptible to road damage from
curbs, speed bumps, or other road obstacles a protective device such as a skid bar or plate should be
installed.
7) To prevent excessive movement and vibration of the exhaust system, install hangers and clamps
designed for use in exhaust systems.
8) Never join or tee the generator exhaust system and the vehicle exhaust system together. Doing so
may cause excessive back pressure on the generator engine, also condensation from one engine can
damage the other engine.
WARNING: LETHAL EXHAUST GAS!
When installing the exhaust system position the tail pipe end so that
discharged exhaust gases are not drawn into the vehicle interior through windows, doors, air conditioners, etc.
During operation an engine discharges deadly carbon monoxide with its exhaust. Carbon monoxide is
particularly dangerous since it is odorless, tasteless, and non-irritating. It can cause death if inhaled for even a
short period of time. Be especially careful if operating the generator set when parked under calm, windless
conditions. Gases may accumulate in these conditions. Park your vehicle so that the exhaust discharges
downwind. Always be aware of others in your vicinity. Make sure that your exhaust discharges away from other
vehicles and buildings.
CAUTION: Make sure the exhaust system components are positioned well away from drain openings beneath
the generator set. Also, be sure not to block access to the oil drain plug.
9
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech PTRV- 3 RR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech PTRV- 3 RR in the language / languages: English as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info