685371
40
Zoom out
Zoom in
Previous page
1/56
Next page
SYSTEMS CONNECTION
REMOTE RADIATOR COOLING SYSTEM
Use the following data in designing and installing the generator set cooling system. To insure a
safe effective installation, be sure the cooling system selected follows these parameters. Power
Technology offers radiator assemblies, which meet these requirements and will adequately cool the
generator. Select the radiator assembly best suited for the generator installation.
Due to the multitude of coach manufacturers and the variety of generator installations, only
general guidelines are provided. Adapt these recommendations to the installation. In a typical
installation the radiator assembly is installed in the same compartment as the generator. If a blower fan
radiator assembly is used, cooling air is drawn across the generator and engine and then through the
radiator. If a suction fan radiator assembly is used the suction fan pulls cooling air through the radiator
and then past the generator set. If the radiator assembly alone is used the installer must supply an electric
blower or suction fan to circulate the cooling air. See the specification table for total air requirements.
Depending on space limitations the radiator can be located in front of, adjacent to, or in a ventilated
remote location from the engine compartment, no more than 10 feet from the generator. To prevent re-
circulation of heated air be sure to maintain a tight seal between the radiator and the discharge chute.
Generally the discharge chute opening should be approximately one and one half times the size of the
radiator core.
NOTE: If the radiator is to be located in a compartment separate from the engine, refer to the engine
combustion air and heat rejection requirements of the generator and engine block when designing the
cooling system. A supplemental cooling fan capable of 500cfm (28.m³/min) should be installed to
supply air to the generator compartment for these requirements.
Connect the radiator fan motor to the generator output leads L1 and L2. Be sure the radiator fan
motor rotates in the correct direction and is of the proper voltage. To protect against overload and short
circuits it is recommended that the motor be adequately fused. Install fuses between the motor and
L1 / L2 connection. A close relationship exists between the cooling system design and the generator
compartment size. Availability of space is often the determining factor in the cooling system design. See
the “Compartment Size” section of this manual prior to designing and installing the generator cooling
system.
CAUTION: The fill inlet and reservoir tank must be located at the highest point in the cooling system.
If the fill inlet is not located as directed, coolant will not completely fill the engine. The cooling system
must be purged of all air pockets for the system to function properly. If air pockets remain in the engine
the high water temperature shutdown switch will malfunction and cause the engine to over heat. Also if
the cooling system is not completely full, the low water level shutdown switch will prevent normal
engine operations.
REMOTE RADIATOR ASSEMBLY
10
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech PTRV- 20K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech PTRV- 20K in the language / languages: English as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info