621129
14
Zoom out
Zoom in
Previous page
1/28
Next page
Chain bar treatment
Uneven wear is the cause of the most frequent problems with
the chain bar. An unauthorised treatment of cutting elements of
the chain and improper depth limiter grinding may amplify that.
If this is the case, replace the chain bar. Check the chain bar
before saw sharpening. A worn-out or damaged chain bar is
not safe and damages the chain, which is why it must not be
used!
Regular chain bar servicing
1. Remove the chain bar off the chain saw.
2. From time to time, remove the wood flour from the chain
bar notch. In doing so, use the glazing or wire knife.
3. Oil grooves to be cleaned after the day when used.
4. Remove any inequality on sides of the chain bar. Use a
blunt file for flat filing of edges.
5. Do not fit the chain bar if bent or cracked or if the inner
rail notch is significantly worn-out.
Do not use clearing baths containing chlorine, carbon
tetrachloride or petrol. The chain bar that is to be replaced
can be received as a spare part.
Saw chain sharpening
The chain must always be sharp!
Cutting is then faster and safer. A blunt chain causes useless
wear of the chain wheel, chain bar, chain and the engine. The
chain is blunt if it needs to be pressed to the wood and the
cutting results in wood flour and some bigger fractions.
Saw chain changing
Change the chain if the cutting elements are too worn-out after
repeated sharpening or if the chain faces a risk of breaking. A
spare chain mentioned in these Operating Instructions to be
used only. The chain wheel must also be changed when
changing the chain. By this, the chain will be driven properly.
Do not use clearing baths containing chlorine, carbon
tetrachloride or petrol. The chain and chain wheel can be
received as a spare part and accessory equipment.
Service
Any technical questions? Complaint? Do you need spare
parts or operation manual?
Go to our website www.guede.com and the section Service
will help you quickly and without bureaucracy. Please, help us
to help you. In order to identify your device in case of
complaint, please indicate serial number, order number and
year of manufacture. All information is available on the product
label. To have all information always at hand, put them down.
Serial number:
Order number:
Year of manufacture:
Phone: +49 (0) 79 04 / 700-480
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts1.guede.com
Troubleshooting
CAUTION: Unplug the chain saw before any servicing. Risk of serious injuries or death as a result of electric shock or
contact with the rotating chain.
Problem
Possible cause Remedy
Saw running but not cutting
Chain fitted the other way round on the chain
bar
See Chain bar and saw chain fitting
Saw cutting only at high speed and it only
results in a few chippings with some bigger
fractions.
Chain is blunt
See Saw chain sharpening
Saw running slowly and remaining
slightly jammed
Voltage is too low
Extension lines are not dimensioned sufficiently
(see Extension line).
Saw engine not starting after pressing the
starter
Switch fuse has not been pressed to release
the starter
Extension line connection is released
Automatic fuse switch is open
Engine brushes are worn out
Electrical circuit on the saw is open
Press the switch fuse before the starter
Check the cable connection
Check the automatic fuse switch
Call an authorised service centre
Call an authorised service centre
Saw engine running but not moving Gear wheel is defective Call an authorised service centre
Chain not being supplied with oil
Oil groove on the chain bar is blocked
Oil is too dense
Remove the chain bar and clean the oil groove
Use the right oil (see Oil tank filling)
Chain getting out of the
chain bar
Chain is too loose
Chain bar and chain are fitted improperly
Tighten the chain. See Chain tension calibration
See Chain bar and saw chain fitting
Saw smoking
Saw is damaged. Do not use the saw
Call an authorised service centre
Oil leaking from the saw
Oil tank cover is not closed
Tighten the oil tank cover. Do not use clearing
baths containing chlorine, carbon tetrachloride
or petrol. Drain the oil tank if the saw is not
being used
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powertec Garden GAK 710 TELE 05167 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powertec Garden GAK 710 TELE 05167 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info