582079
15
Zoom out
Zoom in
Previous page
1/20
Next page
POWXQG4060 EN
Copyright © 2014 VARO P a g e | 15 www.varo.com
Push stop switch down.
Remove knob (A) holding air filter cover in place; remove the top cover (B) by loosening
the cover retaining screw. Cover will lift off. (fig. 18a)
Disconnect the wire connector (C) from the spark plug (D) by pulling and twisting at the
same time (fig. 18b).
Remove spark plug with spark plug socket wrench.
DO NOT USE ANY OTHER TOOL
Check electrode gaps with wire feeler gauge and set gaps to .025” (.635mm) if necessary.
Reinstall a new spark plug.
Note: a resistor spark plug must be used for replacement.
Note: this spark ignition system meets all requirements of the interference-
causing equipment regulations.
11 CLEANING AND MAINTENANCE
11.1 Sprocket tip lubrication:
Caution: the sprocket tip on your new saw has been pre-lubricated at the
factory. Failure to lubricate the guide bar sprocket tip as explained below
will result in poor performance and seizure, voiding the manufacturer’s
warranty.
Lubrication of the sprocket tip is recommended after 25 hours of use or once a week, which
ever occurs first. Always thoroughly clean guide bar sprocket tip before lubrication.
Tools for lubrication:
The lube gun (optional) is recommended for applying grease to the guide bar sprocket tip. The
lube gun is equipped with a needle nose tip which is necessary for the efficient application of
grease to the sprocket tip.
To lubricate sprocket tip:
Warning: wear heavy duty work gloves when handling the bar and chain.
Press the stop switch down.
Note: it is not necessary to remove the saw chain to lubricate the guide bar
sprocket tip. Lubrication can be done on the job.
Clean the guide bar sprocket tip.
Using the lube gun (optional), insert needle nose into the lubrication hole and inject grease
until it appears at outside edge of sprocket tip (fig. 19).
Rotate saw chain by hand. Repeat lubrication procedure until the entire sprocket tip has
been greased.
11.2 Guide bar maintenance:
Most guide bar problems can be prevented merely by keeping the chain saw well maintained.
Insufficient guide bar lubrication and operating the saw with chain that is too tight will
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQG4060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQG4060 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQG4060

Powerplus POWXQG4060 User Manual - German - 23 pages

Powerplus POWXQG4060 User Manual - Dutch - 22 pages

Powerplus POWXQG4060 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info