481028
8
Zoom out
Zoom in
Previous page
1/13
Next page
POWXQ5335 EN
Copyright © 2015 VARO P a g e | 8 www.varo.com
9.2 Dust and chip extraction
For integrated dust extraction, place the dust bag (20) on the sawdust ejector.
For external dust, you can use a vacuum cleaner hose.
The dust bag is only for a partial dust removal! It is designed to break the
dust extraction.
9.3 Clamping the work piece
Make sure the work piece can’t be catapulted. The clamp(12) is the most perfect gadget to
avoid this.
Press the work piece against the fence (4) and between the clamp
Tighten the clamp (12) clockwise to secure the work piece.
9.4 Horizontal mitre angle
The horizontal mitre angle can be set in the range from -45° to 45°. The horizontal mitre angle
scale shows the currently set in degrees.
Loosen the locking knob (6) at the top of the guide rail.
Push the lever (6).
Rotate the saw table (5) to the required angle ( to the right or to the left). The required
angle can be read of the scale flute (8).
Tighten the locking knob (6) clockwise.
9.5 Adjustment of the saw blade and guide rail.
Position the saw in the lower position and block it with the blocking pin.
Now hold the try square (90°) against the guide rail and the saw blade. The latter must
make complete contact with the try square. If this is not the case, then you can adjust the
angle by moving the guide rail. To carry out this step, use the delivered key for loosening
the screws. Do not forget to re-tighten the screws afterwards.
9.6 Vertical bevel angle
The vertical bevel angle can be set in the rang of 0° to 45°. The vertical bevel scale shows the
currently set in degrees.
Loosen the locking lever(22), if tightened.
Swing the tool arm (15) with the handle (18) to the required angle.
Tighten the locking lever (22).
9.7 Adjustment of the saw blade and the base
Position a try square against the saw blade and the sawing table.
If the saw blade is not completely in line, then you can adjust the angle by means of the
screw.
After this, you can adapt the zero position on the graduated scale.
8


Need help? Post your question in this forum.

Forumrules
1

Forum

powerplus-powxq5335

Reset search

  • Is het mogelijk enkel de motor van het type PowXQ5335 te bekomen, bestaande is verbrand Submitted on 17-11-2022 at 15:00

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5335 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5335 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5335

Powerplus POWXQ5335 User Manual - German - 14 pages

Powerplus POWXQ5335 User Manual - Dutch - 13 pages

Powerplus POWXQ5335 User Manual - French - 14 pages

Powerplus POWXQ5335 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info