725417
7
Zoom out
Zoom in
Previous page
1/14
Next page
POWXG6462 EN
Copyright © 2020 VARO P a g e | 7 www.varo.com
If the shredder should start to vibrate abnormally, switch off the motor and check for the
cause immediately. Vibration is generally a warning of trouble.
Ensure blades are secure before shredding. Do not operate the shredder if any of the
blades are not properly mounted.
The shredder should be checked carefully before use. You should only work with a
shredder that is in good condition. If you notice any defect on the machine that may cause
danger to the operator, do not operate the shredder until defects are rectified.
Replace worn or damaged parts for safety. Use only original spare parts. Parts not
produced by manufacturer may cause poor fit and possible injury.
Use the shredder only in places where it is protected from water and never use it outdoors
in rainy weather.
Store in a dry secure place out of reach of children,
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
6.1 Preparation:
Do not allow children to operate this equipment.
Do not operate this equipment in the vanity of bystanders.
Wear ear protection and safety glasses at all times while operating.
Avoid wearing clothing that is loose fitting or that has hanging cords and ties.
Only operate the machine the machine in open space (e.g. Not close to a wall or other
fixed objects) and on a firm, level surface.
Do not operate the machine on a paved or gravel surface, where ejected material could
cause injury.
Before starting the machine, check that all screws, nuts, bolts, and other fasteners are
properly secured and that guards and screens are in place. Replace damaged and
unreadable labels.
6.2 Operation:
Before starting the machine, look into the feeding chamber to make certain, that it is
empty.
Keep your face and body away from the feed intake opening.
Do not allow hands or any other part of the body or clothing inside the feeding chamber,
discharge chute, or near any moving part.
Keep proper balance and footing at all times. Do not overreach. Never stand at a higher
level than the base of the machine, when feeding material into it.
Always stand clear of the discharge zone when operating this machine.
When feeding material into the machine be extremely careful that pieces of metal, rocks,
bottles, cans or other foreign objects are not included.
If the cutting mechanism strikes any foreign objects or if the machine should start making
any unusual noise or vibration, shut off the power source and allow the machine to stop,
disconnect the spark plug wire from the spark plug ( electric unit disconnect from supply)
and take the following steps:
1. Inspect for damage
2. Check for and tighten any loose parts
3. Have any damaged parts replaced or repaired with parts having equivalent specifications
Do not allow processed material to build up in the discharge zone; this may prevent proper
discharge and can result kickback of material through the feed intake opening.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG6462 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG6462 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG6462

Powerplus POWXG6462 User Manual - German - 15 pages

Powerplus POWXG6462 User Manual - Dutch - 15 pages

Powerplus POWXG6462 User Manual - French - 15 pages

Powerplus POWXG6462 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info