582082

Powerplus POWXG30010 Manual

7
Zoom out
Zoom in
Previous page
1/13
Next page
POWXG30010 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
If the engine does not start, go back to step 3.
If the engine stops while squeezing the throttle, go back to step 4.
7.2 Stopping instructions
1. Release the throttle control and allow the engine to cool down by idling.
2. Press and hold the on/off switch in the OFF (0) position until the unit comes to a complete
stop (Fig. 1).
8 OPERATING INSTRUCTIONS
8.1 Holding the unit
Warning: Always wear eye, hearing, foot and body protection to reduce the
risk of injury when operating this unit.
Before operating the unit, stand in the operating position (fig. 3). Check for the following:
The operator is wearing eye protection and proper clothing.
Both hands are holding the handle bar firmly.
The edger wheel is adjusted for proper cut depth as shown in Fig. 4 and edger positions
are as shown in Fig. 3.
8.2 Adjusting edger cutting depth
Gently pull the depth adjustment lever away from the wheel bracket (Fig. 4).
To raise the cutting blade, move the lever toward the front of the wheel bracket (Fig. 4).
Lowering the wheel decreases the cutting depth.
To lower the cutting blade, move the lever toward the rear of the wheel bracket. Raising
the wheel increases the cutting depth.
8.3 Tips for best edging results
After starting the engine, keep the unit tilted back so the blade does not touch the ground.
Move the unit to the desired location and slowly lower the blade into the ground.
Do not force the edger. Edge the first time at a lesser depth, then do the area again with a
deeper setting.
Walk the edger at a slow, even pace.
Check the blade condition (Fig. 5). As it wears it becomes smaller, thus reducing the
cutting depth performance. Replace the blade when it no longer makes contact with the
ground.
9 OIL AND FUEL INFORMATION
Warning: Lack of lubrication voids engine warranty. Gasoline and oil must
be mixed at 40:1.
The engine must use the mixture oil, the mixture ratio is 40:1.
The gasoline should use the 90 octane or 93 octane unleaded gasoline.
The oil should be two-stroke FC special mixing oil.
Fill 585 ml gasoline (position 1) in the pot, and add two-stroke oil up to the 600 ml mark,
then shake it well.
Don’t add too much fuel to the fuel tank, the fuel capacity should be 80 % of the fuel tank,
there should be some space left for gasoline expansion.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG30010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG30010 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG30010

Powerplus POWXG30010 User Manual - German - 15 pages

Powerplus POWXG30010 User Manual - Dutch - 14 pages

Powerplus POWXG30010 User Manual - French - 14 pages

Powerplus POWXG30010 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info